Age | Commit message (Expand) | Author |
2013-02-13 | ipu_common: delay request_irq, check for handler not NULL3.0-boundary-imx6-ts3 | Troy Kisky |
2013-02-13 | sabrelite: mipi camera, turn on pwm3 | Troy Kisky |
2013-02-13 | pwm: add high_perf clock option, fix rounding | Troy Kisky |
2013-02-13 | drm: add defined(__KERNEL__) to fix compile error | Troy Kisky |
2013-02-13 | mx6_sabrelite: setup J12 as CSI1 | Troy Kisky |
2013-02-12 | pcie: add MSI support | Troy Kisky |
2013-02-12 | pcie: fix legacy interrupts for bridge | Troy Kisky |
2013-02-12 | pcie: fix bridge access and bus 1 access | Troy Kisky |
2013-02-12 | pcie: force gen1 speed | Troy Kisky |
2013-02-12 | mx6qsabrelite: export buttons as GPIO if no KEYBOARD_GPIO | Eric Nelson |
2013-02-12 | fec: fix rx error counts | Troy Kisky |
2013-02-12 | fec: stop the "rcv is not +last, " error messages | Troy Kisky |
2013-02-12 | fec: tune RSEM and RSFL values for tapeout 1.0 | Eric Nelson |
2013-02-12 | fec: enable tx/rx of pause frames for mx6q | Troy Kisky |
2013-02-12 | nitrogen6x_defconfig: Add NAPI to match Freescale config, prevent network ins... | Eric Nelson |
2013-02-12 | Thermal changes | Troy Kisky |
2013-02-12 | nitrogen6x_defconfig: sync with latest Kconfig defaults | Eric Nelson |
2013-02-12 | nitrogen6x_defconfig: remove unsupported cameras | Eric Nelson |
2013-02-12 | sgtl5000: set default microphone gain to 2(30dB) to work with commodity PC mics | Eric Nelson |
2013-02-12 | sgtl5000: microphone gain only has 2-bits of resolution, so max is 3 | Eric Nelson |
2013-02-12 | mxc_hdmi: don't require CEA mode | Eric Nelson |
2013-02-12 | mxc_uart_early: don't call clk_disable | Troy Kisky |
2013-02-12 | Nitrogen6 SOM: mipi | Troy Kisky |
2013-02-12 | mx6q_sabrelite: add mx6solo/mx6duallite support | Troy Kisky |
2013-02-12 | board-mx6q_sabrelite: detect Flexcan controller chip | Troy Kisky |
2013-02-12 | Fix detect of focaltech-ft5x06 5-finger multi-touch device. | Sven Van Asbroeck |
2013-02-12 | i.MX6: mx6qsabrelite: add weak pull-up on RGB touch screen interrupt line (GP... | Eric Nelson |
2013-02-12 | nitrogen6x_defconfig: sync with non-Android settings | Eric Nelson |
2013-02-12 | wl12xx_sdio: reset during op_remove_interface | Eric Nelson |
2013-02-12 | wl12xx: add mac override parameter | Troy Kisky |
2013-02-12 | sdio_cis: hack for broken wl127x CIS | Eric Nelson |
2013-02-12 | wl12xx: Kconfig select WIRELESS_EXT and WEXT_PRIV | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabrelite: add vwl1271 regulator | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabre_lite: add wl1271 interface on ESDHC2 | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabrelite: add SD2+WiFi pad setup | Eric Nelson |
2013-02-12 | nitrogen6x_defconfig: add supported hardware/features | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabrelite: Add support for FocalTech ft5x06 driver | Eric Nelson |
2013-02-12 | i.MX6Q: mx6q_sabrelite: Add TSC2004 touch screen support | Eric Nelson |
2013-02-12 | mxcfb_claa_wvga: add fsl_ to mxc_lcd_platform_data, to compile | Troy Kisky |
2013-02-12 | i.MX6: mx6q_sabrelite: Sabre Lite doesn't expose UART3, Nitrogen6W does | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabrelite: set up UART3 (/dev/ttymxc2) with RTS, CTS on pins EIM_... | Eric Nelson |
2013-02-12 | i.MX6Q: mx6q_sabrelite: fix SDHC write-protect pins | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabrelite: route SGTL5000 to audmux 3 on Nitrogen6 | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabrelite: Add Nitrogen6W detection | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabrelite: swap SD cards to have numbering match U-Boot | Eric Nelson |
2013-02-12 | mx6qsabrelite: move HDMI to IPU0/DI1 to separate it from the parallel RGB dis... | Eric Nelson |
2013-02-12 | mxc_ipuv3_fb: enable displays by default (don't BLANK) | Eric Nelson |
2013-02-12 | i.MX6Q: mx6q_sabrelite: Add PWM0 backlight (on DRGB connector) | Eric Nelson |
2013-02-12 | i.MX6: mx6q_sabrelite: add DVFS, MIPI_CSI2, PCIE, PERFMON to automatic Sabre-... | Eric Nelson |
2013-02-12 | mx6q_sabrelite: add pcie support | Eric Nelson |