Age | Commit message (Collapse) | Author |
|
Add support for the SLEEP_MOCI signal to the dsi-to-lvds overlays, this
allows the driver to turn off the the SLEEP_MOCI in suspend.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
Add support for the SEEP_MOCI signal to the dsi-to-hdmi overlay, this
allows the driver to turn off SLEEP_MOCI in suspend.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
Add support for the SLEEP_MOCI signal to the dsi-to-lvds overlays, this
allows the driver to turn off the the SLEEP_MOCI in suspend.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
Add support for the SLEEP_MOCI signal to the dsi-to-hdmi overlay, this
allows the driver to turn off SLEE_MOCI in suspend.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
Add support for the SLEEP_MOCI signal to the dsi-to-lvds overlays, this
allows the driver to turn off the the SLEEP_MOCI in suspend.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
Add support for the SLEEP_MOCI regulator to the dtsi file that is used
by verdin-imx8mm and verdin-imx8mp. The gpio needs to be set in the
corresponding dsi-to-lvds overlay.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
Add support for the SLEEP_MOCI signal to the dsi-to-hdmi overlay, this
allows the driver to turn off SLEEP_MOCI in suspend.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
|
|
The Riverdi 10" Capacitive Touch display is brightest when the PWM
duty cycle is at 100%, i.e. always 1. Thus keep the PWM polarity
at normal.
That way 0: backlight off, 1: backlight dark, 7: backlight bright.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
With the current timings the series production display no longer sync
on the provided signal. The display stays greyish.
Riverdi proposed front/back-porch timing changes. With this the display
work.
Related-to: ELB-5389
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Add overlay to configure the two loudspeaker outputs as a
single Bridge Tied Load output getting higher output power.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
|
|
Remove duplicated verdin-imx8mm_nau8822-btl_overlay.dtbo
that was added by mistake together with am62 overlays.
Fixes: fab825271642 ("verdin-am62: add initial overlay set")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Add overlay for DSI, audio and spidev. MIPI-CSI and LVDS are not
supported in mainline yet, therefore skip those.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Add overlay for Riverdi 10.1 inch capacitive touch panel
connected via DSI.
It can be directly connected to Mallow carrier board and, using Verdin
DSI display adapter, it can be connected to Dev and Dahlia carrier boards.
Related-to: ELB-5365
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
Add overlay for Riverdi 10.1 inch capacitive touch panel
connected via DSI.
It can be directly connected to Mallow carrier board and, using Verdin
DSI display adapter, it can be connected to Dev and Dahlia carrier boards.
Related-to: ELB-5364
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
This commit suppresses compiler warnings about size-cells and
empty range property missing in reserved-memory block.
Fixes: 09f7918e ("verdin-imx8mm: add hmp dt overlay")
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
|
|
Rather than referencing the root node and overriding its compatible,
overlays should have their own root node with their compatible which may
be checked for compatibility prior to being applied by a boot loader.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add Verdin DSI to HDMI Adapter (dsi-to-hdmi) with Lontium LT8912B MIPI
DSI to HDMI bridge chip device tree overlay compatible with mainline/
master/upstream v6.5 Linux kernel and device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add Verdin DSI to LVDS Adapter (dsi-to-lvds) with Capacitive Touch
Display 10.1" LVDS (panel-cap-touch-10inch-lvds) device tree overlay
compatible with mainline/master/upstream v6.5 Linux kernel and device
trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
This overlay enables the imx remoteproc driver and
disables UART4 to make it available for Cortex-M
debugging messages.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
|
|
Add overlay to configure the two loudspeaker outputs as a
single Bridge Tied Load output getting higher output power.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
|
|
Add Verdin DSI to HDMI Adapter (dsi-to-hdmi) with Lontium LT8912B MIPI
DSI to HDMI bridge chip device tree overlay compatible with mainline/
master/upstream v6.5-rc2 Linux kernel and device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add Verdin DSI to LVDS Adapter (dsi-to-lvds) with Capacitive Touch
Display 10.1" LVDS (panel-cap-touch-10inch-lvds) device tree overlay
compatible with mainline/master/upstream v6.5-rc2 Linux kernel and
device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
With moving to kernel 6.5 the kernel commit 724ba67515320 ("ARM: dts:
Move .dts files to vendor sub-directories") introduced a regression
with our 32 bit machines.
Add the new subdirs as part of the list of include paths to search
when using the Makefile to build outside of OE.
Related-to: ELB-5263
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
This overlay adds the tc358743 HDMI to MIPI-CSI2 bridge driver
on the apalis iMX6 camera interface.
Related-to: ELB-5141
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
Add overlay to configure the two loudspeaker outputs as a
single Bridge Tied Load output getting higher output power.
Related-to: ELB-4489
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
|
|
Settings for adapter are wrongly redefined in imx7-colibri-eval-v3.dtsi
which leads to this overlay currently not working.
As a workaround, do redefine these settings again in this overlay.
Related-to: ELB-4830
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
The panel-cap-touch-10inch-lvds_overlay was inadvertently using the
adapter rather than the connector for the atmel-mxt capacitive
touch screen.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit 4b262f28720e12214c92d2c90c94f711ece31448)
Add also to the master branch
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Move the existing overlays to dtsi files and include them into one
accessory dts.
Provide data-mapping timings appropriately for each machine instead
of the hardcoding and use a single overlay per SoC to avoid code
duplication.
Set the bus-format via toradex specific data-mapping property in
the machine specifig overlay.
Make sure the panel-dpi compatible is set correctly in the display
specific overlay.
While at it use new lines consistently and set sensible width and
height dimension for a fullHD analog RGB monitor.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Move the existing overlays to dtsi files and include them into one
accessory dts.
Provide data-mapping timings appropriately for each machine instead
of the hardcoding and use a single overlay per SoC to avoid code
duplication.
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
Move the existing overlays to dtsi files and include them into one
accessory dts.
Provide data-mapping timings appropriately for each machine instead
of the hardcoding and use a single overlay per SoC to avoid code
duplication.
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
Move the existing overlays to dtsi files and include them into one
accessory dts.
Provide data-mapping timings appropriately for each machine instead
of the hardcoding and use a single overlay per SoC to avoid code
duplication.
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This overlay enables the spidev driver on the apalis imx6 spi interface.
Related-to: ELB-4689
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This overlay enables spidev driver on the colibri imx6 spi interface.
Related-to: ELB-4689
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This overlay enables the spidev driver on the colibri imx7 spi interface.
Related-to: ELB-4689
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This overlay enables spidev driver on the colibri iMX6ULL spi interface.
Related-to: ELB-4689
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This commit corrects the indentation, adds a comment about the the
compatible chipname used to bind the spidev driver and removes the
redundant status variable.
Fixes: d929016d ("verdin-imx8mm: add spidev overlay")
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This commit corrects the indentation, adds a comment about the the
compatible chipname used to bind the spidev driver and removes the
redundant status variable.
Fixes: 9282bdc4 ("verdin-imx8mp: add spidev overlay")
Related-to: ELB-4652
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This commit suppresses compiler warnings about address-cells and
size-cells properties missing in spidev block
Fixes: 9282bdc4 ("verdin-imx8mp: add spidev overlay")
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This commit suppresses compiler warnings about address-cells and
size-cells properties missing in spidev block
Fixes: d929016d ("verdin-imx8mm: add spidev overlay")
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This overlay enables spidev by default.
Related-to: ELB-4652
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
This overlay enables spidev by default.
Related-to: ELB-4652
Signed-off-by: Aishwarya Kothari <aishwarya.kothari@toradex.com>
|
|
Fix reset GPIO polarity in-line with the following upstream fix:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit?id=feedaacdadfc332e1a6e436f3adfbc67e244db47
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
Add following overlays:
- Parallel RGB support
- Parallel RGB LVDS support
- Atmel MXT TS for boards with Capacitive Touch Connector
- Atmel MXT TS for Capacitive Touch Adapter
- Toradex 7" resistive touchscreen ad7879
Related-to: ELB-4065
Related-to: ELB-4080
Signed-off-by: Oleksii Bidnichenko <oleksii.bidnichenko@toradex.com>
|
|
When the overlays was converting to the syntactic sugar, the ov5640
driver was sat to the wrong i2c channel. Fix it.
Fixes: 9b0e73d2115d ("apalis-imx6: convert ov5640 v1.1b to syntactic sugar")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The correct name for the node is adv_7280, as declared in
imx6qdl-apalis.dtsi.
Related-to: TOR-1692
Signed-off-by: Sergio Prado <sergio.prado@toradex.com>
|
|
Sort overlays' entries in Makefile alphabetically.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add the overlay to support the LCD-LVDS transceiver on Iris v2.0A
in single-channel RGB24 mode.
Related-to: ELB-3898
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add the overlay to support LCD-LVDS transceiver on Iris v2.0A.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add missing emmc version of the module into the compatible lists.
Related-to: ELB-3849
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|