summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2013-09-09net: mcffec: add support for FEC1 only operationMarcel Ziswiler
Add support for FEC1 only operation in case FEC0 is not used at all.
2013-09-09mtd/nand: fsl_nfc: add option for 8-bit wide bus widthMarcel Ziswiler
Add configuration option CONFIG_NAND_FSL_NFC_8BIT to be able to specify narrow 8-bit wide bus width in connecting NAND chips.
2013-09-08NAND Boot:Dan Douglass
- nb_update tool in fsl_nfc driver rewritten to write FCB, BBT, and image to NAND. - vybrid_nand board config added. - NAND read commands added to DCD that force NFC controller to read NAND page twice to prevent NFC hang.
2012-09-07Add NFC support for faraday boardJason Jin
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2012-09-07Add quad SPI support for VybridJingchang Lu
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2012-09-07Add eSDHC support for Vybrid platformJingchang Lu
On some platform, such as vybrid, there is no scr register, but the dis-order excution may wrongly excute the register write. The barrier used to prevent this. Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2012-09-07Add Vybrid ENET supportJason Jin
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2012-09-07Add UART console support for Vybrid platformJingchang Lu
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2012-09-07Add GPIO support for Vybrid platformJingchang Lu
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2012-03-21cfi: fix the incomplete erased status check in buffer writeTao Hou
Without the fix, flash_write_cfibuffer will terminate the erased status check once an all-0xFF word has been found instead of continuing the erased status check utill the first non-0xFF word. Signed-off-by: Tao Hou <hotforest@gmail.com> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-03-19USB: Armada100: EHCI Driver for Armada100 SOCsAjay Bhargav
This patch adds support for USB EHCI driver for Armada100 SOCs. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2012-03-19USB: Armada100: Add UTMI PHY interface driverAjay Bhargav
This patch adds USB host controller's UTMI PHY interface driver for Armada100 SOCs. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2012-03-19usb:udc:samsung:fix Remove the req_config flagŁukasz Majewski
The dev->req_config flag was indicating that the forwarded request needs to perform the usb gadget delayed status. This is however not needed anymore, so it can be removed. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Vasut <marex@denx.de>
2012-03-19USB:gadget:designware Fix memory nonalignment issueShiraz Hashim
While receiving packets from FIFO sometimes the buffer provided was nonaligned. Fix this by taking a temporary aligned buffer and then copying the content to nonaligned buffer. Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-03-19USB:gadget:designware Make locally used functions staticAmit Virdi
Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-03-19USB:gadget:designware Support high speedVipin KUMAR
This patch adds the support for usb device high speed for designware peripheral. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-03-19USB:gadget:designware Device controller bugfixesVipin KUMAR
This patch fixes a few bugs in USB device controller driver. The fixes are as follows 1. Adding error condition checks eg. NULL return 2. Endpoint other than endpoint 0 (control endpoint) are initialized only if usb state machine reaches STATE_ADDRESSED or above 3. Zero length packet handling corrected 4. Dead code removed 5. Bulk out endpoint returns after servicing 1 interrupt and returns back to service if more interrupts are pending Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Marek Vasut <marex@denx.de>
2012-03-19USB:gadget:designware USB device controller (UDC) implementationVipin KUMAR
The earlier usb device controller driver was specific to spear platforms. This patch implements the usb device controller driver as a generic controller which can be reused by other platforms using this peripheral. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Marek Vasut <marex@denx.de>
2012-03-19usb: replace wait_ms() with mdelay()Mike Frysinger
Common code has a mdelay() func, so use that instead of the usb-specific wait_ms() func. This also fixes the build errors: ohci-hcd.c: In function 'submit_common_msg': /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1519:9: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1816:10: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1827:10: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1844:10: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1563:11: sorry, unimplemented: called from here /usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available ohci-hcd.c:1583:9: sorry, unimplemented: called from here make[1]: *** [ohci-hcd.o] Error 1 Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Marek Vasut <marex@denx.de>
2012-03-19usb: musb: fix printf warningMike Frysinger
musb_hcd.c: In function 'musb_submit_rh_msg': musb_hcd.c:827:2: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int' Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-03-18net/miiphy/serial: drop duplicate "NAMESIZE" defineMike Frysinger
A few subsystems are using the same define "NAMESIZE". This has been working so far because they define it to the same number. However, I want to change the size of eth_device's NAMESIZE, so rather than tweak the define names, simply drop references to it. Almost no one does, and the handful that do can easily be changed to a sizeof(). Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-03-17Merge branch 'master' of git://git.denx.de/u-boot-avr32Wolfgang Denk
* 'master' of git://git.denx.de/u-boot-avr32: atmel_mci.h: remove outdated register macros doc/git-mailrc: add <me> to avr32 alias ATMEL: remove old atmel_mci driver ATMEL: use generic mmc framework
2012-03-17Merge branch 'sandbox' of git://git.denx.de/u-boot-blackfinWolfgang Denk
* 'sandbox' of git://git.denx.de/u-boot-blackfin: sandbox: mark os_exit as noreturn sandbox: add getopt support sandbox: allow processing before main loop sandbox: add concept of sandbox state sandbox: disable fortification sandbox: u-boot.lds: tweak style sandbox: add get_{tbclk,ticks} sandbox: enable GPIO driver sandbox: gpio: add basic driver for simulating GPIOs sandbox: add flags for open() call sandbox: config: enable fdt and snprintf() options sandbox: fdt: add support for CONFIG_OF_CONTROL sandbox: add lseek helper sandbox: add ifdef protection to os.h sandbox: add required header to os.c sandbox: sort header files in os.c
2012-03-13ATMEL: remove old atmel_mci driverSven Schnelle
All boards are using the gen_atmel_mci driver now, so no need to carry the old driver around. Signed-off-by: Sven Schnelle <svens@stackframe.org> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-03-13ATMEL: use generic mmc frameworkSven Schnelle
gen_atmel_mci works on AVR32 as well, so no need to use the legacy mmc driver. This also has the nice side effect of being able to use SDHC cards an those boards. Signed-off-by: Sven Schnelle <svens@stackframe.org> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-03-12sandbox: gpio: add basic driver for simulating GPIOsSimon Glass
This provides a way of simulating GPIOs by setting values which are seen by the normal gpio_get/set_value() calls. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-03-08sh: Fix sh7264 clock speed and related serial settingPhil Edworthy
The generalised calculation of the serial bit rate reg also applies to sh7264, it was just the clock speed that was set incorrectly. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-03-08net: sh_eth: Remove unnecessary returnNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-03-08net: sh_eth: Collect up EDMR_INIT_CNT to TIMEOUT_CNTNobuhiro Iwamatsu
EDMR_INIT_CNT holds the check count of initialization. Since there were more same values (1000), this collected as TIMEOUT_CNT. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-03-08net: sh_eth: Remove SH_ETH_PHY_DELAYNobuhiro Iwamatsu
SH_ETH_PHY_DELAY is not used. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-03-08sh: sh_eth: Add support SH7724Nobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-03-04Remove execute permissions from source filesThomas Weber
Signed-off-by: Thomas Weber <weber@corscience.de>
2012-03-04pci: move pciauto_config_init() to pci.hLinus Walleij
Fixing build regressions for the Integrator I get find that a few boards try to work around the missing declaration of pciauto_config_init() by declaring it in the local scope. This does not make sense when the sibling functions are in <pci.h> so move the function to the header, ridding the build error in the Integrator and getting rid of the local declarations here and there. Reported-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-03USB: move keyboard polling into kbd driveramartin@nvidia.com
This moves keyboard polling logic from USB HCD drivers into USB keyboard driver. Remove usb_event_poll() as keyboard polling was the only user of this API. With this patch USB keyboard works with EHCI controllers again. Tested on a tegra2 seaboard. Signed-off-by: Allen Martin <amartin@nvidia.com>
2012-03-03eth: remove usb-ethernet devices before re-enumerating themVincent Palatin
Fix the crash when running several times usb_init() with a USB ethernet device plugged. Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Tested-by: Wolfgang Grandegger <wg@denx.de>
2012-03-03Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk
* 'master' of git://git.denx.de/u-boot-nand-flash: cmd_nand.c: Fix 'nand dump' after latest MTD resync mtd/nand:Fix wrong usage of is_blank() in fsl_ifc_run_command mtd/nand: Fix IFC driver to support 2K NAND page nand: reinstate lazy bad block scanning Revert "nand: make 1-bit software ECC configurable"
2012-02-28mtd/nand:Fix wrong usage of is_blank() in fsl_ifc_run_commandPrabhakar Kushwaha
Freescale IFC NAND Machine calculates ECC on 512byte sector and same is used in fsl_ifc_run_command() during ECC status verification. Also this sector is passed to is_blank() for blank checking. It is wrong at first place because is_blank()'s implementation checks for Page size and OOB area size. is_blank() should be called per page for main and OOB area verification. Variables name are redefined to avoid confusion between buffer and ecc sector. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-02-28mtd/nand: Fix IFC driver to support 2K NAND pagePrabhakar Kushwaha
1) OOB area should be updated irrespective of NAND page size. Earlier it was updated only for 512byte NAND page. 2) During OOB update fbcr should be equal to OOB size. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-02-28nand: reinstate lazy bad block scanningScott Wood
commit 2a8e0fc8b3dc31a3c571e439fbf04b882c8986be ("nand: Merge changes from Linux nand driver") accidentally reverted commit 13f0fd94e3cae6f8a0d9fba5d367e311edc8ebde ("NAND: Scan bad blocks lazily."). Reinstate the change, as amended by commit ff49ea8977b56916edd5b1766d9939010e30b181 ("NAND: Mark the BBT as scanned prior to calling scan_bbt."). Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-02-28Revert "nand: make 1-bit software ECC configurable"Scott Wood
This reverts commit 4fee6c2f295f932b8febdc7ce8731ba045695fa5. It breaks boards that currently rely on soft-ecc, as pointed out here: http://patchwork.ozlabs.org/patch/140872/ The reverted patch should be resubmitted with documentation, and with the CONFIG_MTD_ECC_SOFT selected from every board that needs it. We could start by looking at what NAND driver the board selects, and whether that driver ever asks for soft ECC. Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-02-27net: phy: make board_phy_config responsible for calling drv->configTroy Kisky
Boards may have things they want done before or after normal phy config. Letting the boards call drv->config allows them more flexibilty. Boards affected by this change are corenet_ds and mpc8544ds. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-27net: phy: add support for Micrel's KSZ9021Troy Kisky
Add the gigabit phy KSZ9021. Also, add function ksz9021_phy_extended_write /_read for access to the phys extended registers. The environment variable "disable_giga" can be used to disable 1000baseTx. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-27net: fec_mxc: add PHYLIB supportTroy Kisky
Surround non PHYLIB routines miiphy_restart_aneg and miiphy_wait_aneg with ifndef CONFIG_PHYLIB. When later PHYLIB is required it is easy to delete the non-PHYLIB code. This separation idea came from Andy Fleming. fec_miiphy_read, and fec_miiphy_write changed to fec_phy_read, and fec_phy_write with argument changes. Deprecated miiphy_register is no longer used. Both old and new PHYLIB code now use mdio_register. Cleanup some debug prints. Inline function fec_miiphy_fec_to_eth is no longer necessary. Moved to the single call location. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-02-27net: fec_mxc: add 1000 Mbps selectionTroy Kisky
Define FEC_QUIRK_ENET_MAC and add to arch-mx6/imx-regs.h Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-27mxc_spi: move machine specifics into CPU headersEric Nelson
Move (E)CSPI register declarations into the imx-regs.h files for each supported CPU Introduce two new macros to control conditional setup MXC_CSPI - Used for processors with the Configurable Serial Peripheral Interface (MX3x) MXC_ECSPI - For processors with Enhanced Configurable... (MX5x, MX6x) Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
2012-02-21Revert "ARM: I2C: I2C Multi byte address support"Tom Rini
This reverts commits 2faa76196af4b3e93bcb9e38ed9090cbd3b06db3 as this has introduced some large problems on all other platforms and have more changes in them than the commit message implies. Cc: Heiko Schocher <hs@denx.de> Cc: Patil, Rachna <rachna@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-02-21Revert "ARM: AM33XX: Add AM33XX I2C driver support"Tom Rini
This reverts commit 498cbdfe62a8330f6c89765bdd15e60328a26511 as we need to revert the i2c changes that add the support for the platform. Cc: Heiko Schocher <hs@denx.de> Cc: Patil, Rachna <rachna@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-02-17Merge branch 'master' of git://git.denx.de/u-boot-mmcWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mmc: mmc: make mmc_send_status() more reliable mmc: fix card busy polling Tegra: mmc: Fixed handling of interrupts in timeouts. omap_hsmmc: Wait for CMDI to be clear
2012-02-17Merge branch 'trini@ti.com' of git://git.denx.de/u-boot-stagingWolfgang Denk
* 'trini@ti.com' of git://git.denx.de/u-boot-staging: usb_ether: fix typo cmd_eeprom: typo doc: complete, typos
2012-02-15mmc: make mmc_send_status() more reliableJan Kloetzke
Align the card status polling with the Linux kernel and retry the command at least five times. Also some cards apparently mishandle the status bits, so make sure to check the card state too. Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com> Cc: Andy Fleming <afleming@gmail.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-16 15:00:40 +0000