diff options
| -rw-r--r-- | README | 38 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/cpu_init.c | 12 | ||||
| -rw-r--r-- | arch/powerpc/cpu/mpc85xx/fdt.c | 2 | ||||
| -rw-r--r-- | drivers/net/fm/fm.c | 32 | ||||
| -rw-r--r-- | drivers/qe/qe.c | 4 | ||||
| -rw-r--r-- | include/configs/MPC8569MDS.h | 3 | ||||
| -rw-r--r-- | include/configs/P1023RDS.h | 10 | ||||
| -rw-r--r-- | include/configs/P2041RDB.h | 16 | ||||
| -rw-r--r-- | include/configs/corenet_ds.h | 16 | ||||
| -rw-r--r-- | include/configs/p1_p2_rdb_pc.h | 5 |
10 files changed, 94 insertions, 44 deletions
@@ -3274,6 +3274,44 @@ Low Level (hardware related) configuration options: be used if available. These functions may be faster under some conditions but may increase the binary size. +Freescale QE/FMAN Firmware Support: +----------------------------------- + +The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the +loading of "firmware", which is encoded in the QE firmware binary format. +This firmware often needs to be loaded during U-Boot booting, so macros +are used to identify the storage device (NOR flash, SPI, etc) and the address +within that device. + +- CONFIG_SYS_QE_FMAN_FW_ADDR + The address in the storage device where the firmware is located. The + meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro + is also specified. + +- CONFIG_SYS_QE_FMAN_FW_LENGTH + The maximum possible size of the firmware. The firmware binary format + has a field that specifies the actual size of the firmware, but it + might not be possible to read any part of the firmware unless some + local storage is allocated to hold the entire firmware first. + +- CONFIG_SYS_QE_FMAN_FW_IN_NOR + Specifies that QE/FMAN firmware is located in NOR flash, mapped as + normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the + virtual address in NOR flash. + +- CONFIG_SYS_QE_FMAN_FW_IN_NAND + Specifies that QE/FMAN firmware is located in NAND flash. + CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash. + +- CONFIG_SYS_QE_FMAN_FW_IN_MMC + Specifies that QE/FMAN firmware is located on the primary SD/MMC + device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device. + +- CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH + Specifies that QE/FMAN firmware is located on the primary SPI + device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device. + + Building the Software: ====================== diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index 27aa038d58..2e4a06c35a 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -39,7 +39,7 @@ #include <asm/fsl_serdes.h> #include <linux/compiler.h> #include "mp.h" -#ifdef CONFIG_SYS_QE_FW_IN_NAND +#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND #include <nand.h> #include <errno.h> #endif @@ -552,17 +552,17 @@ void cpu_secondary_init_r(void) { #ifdef CONFIG_QE uint qe_base = CONFIG_SYS_IMMR + 0x00080000; /* QE immr base */ -#ifdef CONFIG_SYS_QE_FW_IN_NAND +#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND int ret; - size_t fw_length = CONFIG_SYS_QE_FW_LENGTH; + size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH; /* load QE firmware from NAND flash to DDR first */ - ret = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FW_IN_NAND, - &fw_length, (u_char *)CONFIG_SYS_QE_FW_ADDR); + ret = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FMAN_FW_IN_NAND, + &fw_length, (u_char *)CONFIG_SYS_QE_FMAN_FW_ADDR); if (ret && ret == -EUCLEAN) { printf ("NAND read for QE firmware at offset %x failed %d\n", - CONFIG_SYS_QE_FW_IN_NAND, ret); + CONFIG_SYS_QE_FMAN_FW_IN_NAND, ret); } #endif qe_init(qe_base); diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c index a53a31d4c5..62c7ea15d0 100644 --- a/arch/powerpc/cpu/mpc85xx/fdt.c +++ b/arch/powerpc/cpu/mpc85xx/fdt.c @@ -466,7 +466,7 @@ void fdt_fixup_fman_firmware(void *blob) return; } - if (length > CONFIG_SYS_FMAN_FW_LENGTH) { + if (length > CONFIG_SYS_QE_FMAN_FW_LENGTH) { printf("Fman firmware at %p is too large (size=%u)\n", fmanfw, length); return; diff --git a/drivers/net/fm/fm.c b/drivers/net/fm/fm.c index 846c37249b..0b8c33fb7a 100644 --- a/drivers/net/fm/fm.c +++ b/drivers/net/fm/fm.c @@ -25,11 +25,11 @@ #include "fm.h" #include "../../qe/qe.h" /* For struct qe_firmware */ -#ifdef CONFIG_SYS_QE_FW_IN_NAND +#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND #include <nand.h> #elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH) #include <spi_flash.h> -#elif defined(CONFIG_SYS_QE_FW_IN_MMC) +#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_MMC) #include <mmc.h> #endif @@ -363,21 +363,21 @@ int fm_init_common(int index, struct ccsr_fman *reg) { int rc; char env_addr[32]; -#if defined(CONFIG_SYS_FMAN_FW_ADDR) - void *addr = (void *)CONFIG_SYS_FMAN_FW_ADDR; -#elif defined(CONFIG_SYS_QE_FW_IN_NAND) - size_t fw_length = CONFIG_SYS_FMAN_FW_LENGTH; - void *addr = malloc(CONFIG_SYS_FMAN_FW_LENGTH); +#if defined(CONFIG_SYS_QE_FMAN_FW_IN_NOR) + void *addr = (void *)CONFIG_SYS_QE_FMAN_FW_ADDR; +#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_NAND) + size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH; + void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH); - rc = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FW_IN_NAND, + rc = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FMAN_FW_ADDR, &fw_length, (u_char *)addr); if (rc == -EUCLEAN) { printf("NAND read of FMAN firmware at offset 0x%x failed %d\n", - CONFIG_SYS_QE_FW_IN_NAND, rc); + CONFIG_SYS_QE_FMAN_FW_ADDR, rc); } #elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH) struct spi_flash *ucode_flash; - void *addr = malloc(CONFIG_SYS_FMAN_FW_LENGTH); + void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH); int ret = 0; ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS, @@ -385,17 +385,17 @@ int fm_init_common(int index, struct ccsr_fman *reg) if (!ucode_flash) printf("SF: probe for ucode failed\n"); else { - ret = spi_flash_read(ucode_flash, CONFIG_SYS_QE_FW_IN_SPIFLASH, - CONFIG_SYS_FMAN_FW_LENGTH, addr); + ret = spi_flash_read(ucode_flash, CONFIG_SYS_QE_FMAN_FW_ADDR, + CONFIG_SYS_QE_FMAN_FW_LENGTH, addr); if (ret) printf("SF: read for ucode failed\n"); spi_flash_free(ucode_flash); } -#elif defined(CONFIG_SYS_QE_FW_IN_MMC) +#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_MMC) int dev = CONFIG_SYS_MMC_ENV_DEV; - void *addr = malloc(CONFIG_SYS_FMAN_FW_LENGTH); - u32 cnt = CONFIG_SYS_FMAN_FW_LENGTH / 512; - u32 blk = CONFIG_SYS_QE_FW_IN_MMC / 512; + void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH); + u32 cnt = CONFIG_SYS_QE_FMAN_FW_LENGTH / 512; + u32 blk = CONFIG_SYS_QE_FMAN_FW_ADDR / 512; struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV); if (!mmc) diff --git a/drivers/qe/qe.c b/drivers/qe/qe.c index c4ec2f4af8..9f711519ed 100644 --- a/drivers/qe/qe.c +++ b/drivers/qe/qe.c @@ -170,11 +170,11 @@ void qe_init(uint qe_base) /* Init the QE IMMR base */ qe_immr = (qe_map_t *)qe_base; -#ifdef CONFIG_SYS_QE_FW_ADDR +#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NOR /* * Upload microcode to IRAM for those SOCs which do not have ROM in QE. */ - qe_upload_firmware((const struct qe_firmware *) CONFIG_SYS_QE_FW_ADDR); + qe_upload_firmware((const void *)CONFIG_SYS_QE_FMAN_FW_ADDR); /* enable the microcode in IRAM */ out_be32(&qe_immr->iram.iready,QE_IRAM_READY); diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index ab27b9895a..7a5d86d2b7 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -510,7 +510,8 @@ extern unsigned long get_clock_freq(void); #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* QE microcode/firmware address */ -#define CONFIG_SYS_QE_FW_ADDR 0xfff00000 +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xfff00000 /* * BOOTP options diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h index 013a6acdca..e057b1f945 100644 --- a/include/configs/P1023RDS.h +++ b/include/configs/P1023RDS.h @@ -526,12 +526,14 @@ extern unsigned long get_clock_freq(void); #ifndef CONFIG_NAND /* Default address of microcode for the Linux Fman driver */ /* QE microcode/firmware address */ -#define CONFIG_SYS_FMAN_FW_ADDR 0xEF000000 +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000 #else -#define CONFIG_SYS_QE_FW_IN_NAND 0x1f00000 +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x1f00000 #endif -#define CONFIG_SYS_FMAN_FW_LENGTH 0x10000 -#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_FMAN_FW_LENGTH) +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) #ifdef CONFIG_FMAN_ENET #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2 diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index f9fe3cf952..a48055e2c5 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -414,21 +414,25 @@ unsigned long get_board_sys_clk(unsigned long dummy); * env is stored at 0x100000, sector size is 0x10000, ucode is stored after * env, so we got 0x110000. */ -#define CONFIG_SYS_QE_FW_IN_SPIFLASH 0x110000 +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 #elif defined(CONFIG_SDCARD) /* * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is * about 545KB (1089 blocks), Env is stored after the image, and the env size is * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. */ -#define CONFIG_SYS_QE_FW_IN_MMC (512 * 1130) +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) #elif defined(CONFIG_NAND) -#define CONFIG_SYS_QE_FW_IN_NAND (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) #else -#define CONFIG_SYS_FMAN_FW_ADDR 0xEF000000 +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000 #endif -#define CONFIG_SYS_FMAN_FW_LENGTH 0x10000 -#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_FMAN_FW_LENGTH) +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) #ifdef CONFIG_SYS_DPAA_FMAN #define CONFIG_FMAN_ENET diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index bc0aeebb44..0622b9fcfd 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -474,21 +474,25 @@ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after * env, so we got 0x110000. */ -#define CONFIG_SYS_QE_FW_IN_SPIFLASH 0x110000 +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 #elif defined(CONFIG_SDCARD) /* * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is * about 545KB (1089 blocks), Env is stored after the image, and the env size is * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. */ -#define CONFIG_SYS_QE_FW_IN_MMC (512 * 1130) +#define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) #elif defined(CONFIG_NAND) -#define CONFIG_SYS_QE_FW_IN_NAND (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) #else -#define CONFIG_SYS_FMAN_FW_ADDR 0xEF000000 +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000 #endif -#define CONFIG_SYS_FMAN_FW_LENGTH 0x10000 -#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_FMAN_FW_LENGTH) +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) #ifdef CONFIG_SYS_DPAA_FMAN #define CONFIG_FMAN_ENET diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index 5a69902f89..8e8fa163b8 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -677,8 +677,9 @@ #ifdef CONFIG_QE /* QE microcode/firmware address */ -#define CONFIG_SYS_QE_FW_ADDR 0xefec0000 -#define CONFIG_SYS_QE_FW_LENGTH 0x10000 +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xefec0000 +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 #endif /* CONFIG_QE */ #ifdef CONFIG_P1025RDB |