Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
  arm: jadecpu: Readd MACH_TYPE_JADECPU
  at91: defined mach-types for otc570 board in board config file
  at91: defined mach-types for meesc board in board config file
  mx31pdk: Enable D and I caches
  ehci-mxc: remove incorrect comment
  README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
  mx53: Turn off child clocks before reconfigure perclk_root
  qong: enable support for compressed images
  imx: imx31_phycore.h: fix checkpatch warnings
  vision2: Remove unused get_board_rev function
  mx53smd: Remove unused get_board_rev function
  mx53ard: Remove unused get_board_rev function
  mx53evk: Remove unused get_board_rev function
  mx53evk: Add RTC support
  mx53loco: Remove unused get_board_rev function
  mx53evk: Remove unneeded '1' from mx53evk.h
  OMAP3: mvblx: Initial support for mvBlueLYNX-X
  ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
  omap3: mem: Move comments next to definitions
  omap3: mem: Clean-up whitespaces
  omap3: mem: Define and use common macros
  Davinci: ea20: added PREBOOT to configuration
  Davinci: ea20: added I2C support
  Davinci: ea20: added video support
  VIDEO: davinci: add framebuffer to da8xx
  ARM: Davinci: added missing registers to hardware.h
  Davinci: ea20: add gpios for LCD backlight control
  Davinci: ea20: add gpio for keeping power on in board_late_init
  Davinci: ea20: Add default U-Boot environment
  Davinci: ea20: Add early init to get early output from console
  Davinci: ea20: Add NAND support
  Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
  Davinci: ea20: set console on UART0
  arm, davinci: add cam_enc_4xx support
  arm926ejs, davinci: add missing spi defines for dm365
  arm926ejs, davinci: add cpuinfo for dm365
  arm, davinci: add lowlevel function for dm365 soc
  arm, davinci: add header files for dm365
  spl, nand: add 4bit HW ecc oob first nand_read_page function
  arm, davinci: add support for new spl framework
  spl: add option for adding post memory test to the SPL framework
  net, davinci_emac: make clock divider in MDIO control register configurable
  arm, usb, davinci: make USBPHY_CTL register configurable
  usb, davinci: add enable_vbus() weak function
  omap3evm: fix errors caused by multiple definitions
  omap3evm: Add (quick) configuration for NAND only
  omap3evm: Add (quick) configuration for MMC/SD only
  omap3evm: move common config options to new file
  omap3evm: Prepare to split configuration
  omap3evm: Reorder related config options
  omap/spl: actually enable the console
  davinci_emac: compilation fix, phy is array now
  omap3evm: Set environment variable 'ethaddr'
  arm, arm926: fix missing symbols in NAND_SPL mode
  arm, davinci: Add function lpsc_syncreset()
  arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
  arm/km: portl2 environment address update to P1B
  arm/km: adapt bootcounter evaluation
  arm/km: enable jffs2 cmds
  arm/km: trigger reconfiguration for the Xilinx FPGA
  arm/km: add boardid and hwkey to kernel command line
  ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
  netspace_v2: enable I2C EEPROM support
  netspace_v2: fix SDRAM configuration
  armada100: define CONFIG_SYS_CACHELINE_SIZE
  pantheon: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: drop empty asm-offsets.s file
  arm/km/mgcoge3un: enhance "waitforne" feature
  arm/km: add variable waitforne to mgcoge3un
  gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
  ARM: dreamplug: fix compilation
  ARM: DockStar: fix compilation
  ARM: netspace_v2: fix warnings
  am335x: Drop board_sysinfo struct
  am335x: Temporarily add MACH_TYPE define
  misc:pmic:samsung Enable PMIC driver at C210 Universal target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
  smdkv310: use macro for mmc data read function address
  smdkv310: use spl framework for mmc spl
  SMDKV310: use get_ram_size() to validate dram size
  SMDKV310: Initialize board id using CONFIG_MACH_TYPE
  ORIGEN : use absolute paths and fix tool naming
  ORIGEN : enable device tree support
  MX25: tx25: Fix building due to missing MACH_TYPE
  mx31: Add board support for HALE TT-01
  mx31: add ESD control registers
  mx31: define pins and init for UART2 and CSPI3
  MX35: add support for flea3 board
  MX51: vision2: add MACH_TYPE in config file
  vision2: Remove unused header file
  mx51evk: Remove unused get_board_rev function
  mx51evk: Remove unneeded '1' from mx51evk.h
  I2C: Fix mxc_i2c.c problem on imx31_phycore
  mx35pdk: Add RTC support
  mx51evk: Use GPIO API for configuring the IOMUX
  mx51evk: Add RTC support
  rtc: Make mc13783-rtc driver generic
  qong: remove unneeded IOMUX settings
  qong: Use mx31_set_gpr to setup USBH2 pins
  mx31: Introduce mx31_set_gpr function
  mx31pdk: Add MC13783 PMIC support
  qong: remove unneeded "1" from qong.h
  misc: pmic: fix regression in pmic_fsl.c (SPI)
  mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
  MX35: Drop unnecessary prototypes from imx-regs.h
  I2C: added I2C-2 and I2C-3 to MX35
  MX35: factorize common assembly code
  MX35: add reset cause as provided by other i.MX
  MX35: add pins definition for UART3
  MX35: added ESDC structure to imx-regs

3 files changed, 148 insertions, 0 deletions

diff --git a/doc/README.SPL b/doc/README.SPL
index b4500fc42b..89d24a7205 100644
--- a/doc/README.SPL
+++ b/doc/README.SPL
@@ -63,3 +63,5 @@ CONFIG_SPL_LIBGENERIC_SUPPORT (lib/libgeneric.o)
 CONFIG_SPL_POWER_SUPPORT (drivers/power/libpower.o)
 CONFIG_SPL_NAND_SUPPORT (drivers/mtd/nand/libnand.o)
 CONFIG_SPL_DMA_SUPPORT (drivers/dma/libdma.o)
+CONFIG_SPL_POST_MEM_SUPPORT (post/drivers/memory.o)
+CONFIG_SPL_NAND_LOAD (drivers/mtd/nand/nand_spl_load.o)
diff --git a/doc/README.davinci.nand_spl b/doc/README.davinci.nand_spl
new file mode 100644
index 0000000000..f46721a00e
--- /dev/null
+++ b/doc/README.davinci.nand_spl
@@ -0,0 +1,141 @@
+With this approach, we don't need the UBL any more on DaVinci boards.
+A "make boardname" will compile a u-boot.ubl, with UBL Header, which is
+needed for the RBL to find the "UBL", which actually is a  UBL-compatible
+header, nand spl code and u-boot code.
+
+
+As the RBL uses another read function as the "standard" u-boot,
+we need a command, which switches between this two read/write
+functions, so we can write the UBL header and the spl
+code in a format, which the RBL can read. This is realize
+(at the moment in board specific code) in the u-boot command
+nandrbl
+
+nandrbl without arguments returns actual mode (rbl or uboot).
+with nandrbl mode (mode = "rbl" or "uboot") you can switch
+between the two NAND read/write modes.
+
+
+To set up mkimage you need a config file for mkimage, example:
+board/ait/cam_enc_4xx/ublimage.cfg
+
+For information about the configuration please see:
+doc/README.ublimage
+
+Example for the cam_enc_4xx board:
+On the cam_enc_4xx board we have a NAND flash with blocksize = 0x20000 and
+pagesize = 0x800, so the u-boot.ubl image (which you get with:
+"make cam_enc_4xx") looks like this:
+
+00000000  00 ed ac a1 20 00 00 00  06 00 00 00 05 00 00 00  |.... ...........|
+00000010  00 00 00 00 20 00 00 00  ff ff ff ff ff ff ff ff  |.... ...........|
+00000020  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
+*
+00000800  14 00 00 ea 14 f0 9f e5  10 f0 9f e5 0c f0 9f e5  |................|
+00000810  08 f0 9f e5 04 f0 9f e5  00 f0 9f e5 04 f0 1f e5  |................|
+00000820  00 01 00 00 78 56 34 12  78 56 34 12 78 56 34 12  |....xV4.xV4.xV4.|
+[...]
+*
+00001fe0  00 00 00 00 00 00 00 00  ff ff ff ff ff ff ff ff  |................|
+00001ff0  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
+*
+00003800  14 00 00 ea 14 f0 9f e5  14 f0 9f e5 14 f0 9f e5  |................|
+00003810  14 f0 9f e5 14 f0 9f e5  14 f0 9f e5 14 f0 9f e5  |................|
+00003820  80 01 08 81 e0 01 08 81  40 02 08 81 a0 02 08 81  |........@.......|
+
+In the first "page" of the image, we have the UBL Header, needed for
+the RBL to find the spl code.
+
+The spl code starts in the second "page" of the image, with a size
+defined by:
+
+#define CONFIG_SYS_NROF_PAGES_NAND_SPL	6
+
+After the spl code, there comes the "real" u-boot code
+@ (6 + 1) * pagesize = 0x3800
+
+------------------------------------------------------------------------
+Setting up spl code:
+
+/*
+ * RBL searches from Block n (n = 1..24)
+ * so we can define, how many UBL Headers
+ * we write before the real spl code
+ */
+#define CONFIG_SYS_NROF_UBL_HEADER	5
+#define CONFIG_SYS_NROF_PAGES_NAND_SPL	6
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	((CONFIG_SYS_NROF_UBL_HEADER * \
+					CONFIG_SYS_NAND_BLOCK_SIZE) + \
+					(CONFIG_SYS_NROF_PAGES_NAND_SPL) * \
+					CONFIG_SYS_NAND_PAGE_SIZE)
+------------------------------------------------------------------------
+
+Burning into NAND:
+
+step 1:
+The RBL searches from Block n ( n = 1..24) on page 0 for valid UBL
+Headers, so you have to burn the UBL header page from the u-boot.ubl
+image to the blocks, you want to have the UBL header.
+!! Don;t forget to switch to rbl nand read/write functions with
+   "nandrbl rbl"
+
+step 2:
+You need to setup in the ublimage.cfg, where the RBL can find the spl
+code, and how big it is.
+
+!! RBL always starts reading from page 0 !!
+
+For the AIT board, we have:
+PAGES		6
+START_BLOCK	5
+
+So we need to copy the spl code to block 5 page 0
+!! Don;t forget to switch to rbl nand read/write functions with
+   "nandrbl rbl"
+
+step 3:
+You need to copy the u-boot image to the block/page
+where the spl code reads it (CONFIG_SYS_NAND_U_BOOT_OFFS)
+!! Don;t forget to switch to rbl nand read/write functions with
+   "nandrbl uboot", which is default.
+
+On the cam_enc_4xx board it is:
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(0xc0000)
+
+-> this results in following NAND usage on the cam_enc_4xx board:
+
+addr
+
+20000		possible UBL Header
+40000		possible UBL Header
+60000		possible UBL Header
+80000		possilbe UBL Header
+a0000		spl code
+c0000		u-boot code
+
+The above steps are executeed through the following environment vars:
+(using 80000 as address for the UBL header)
+
+pagesz=800
+uboot=/tftpboot/cam_enc_4xx/u-boot.ubl
+load=tftp 80000000 ${uboot}
+writeheader nandrbl rbl;nand erase 80000 ${pagesz};nand write 80000000 80000 ${pagesz};nandrbl uboot
+writenand_spl nandrbl rbl;nand erase a0000 3000;nand write 80000800 a0000 3000;nandrbl uboot
+writeuboot nandrbl uboot;nand erase c0000 5d000;nand write 80003800 c0000 5d000
+update=run load writeheader writenand_spl writeuboot
+
+If you do a "run load update" u-boot, spl + ubl header
+are magically updated ;-)
+
+Note:
+- There seem to be a bug in the RBL code (at least on my HW),
+  In the UBL block, I can set the page to values != 0, so it
+  is possible to burn step 1 and step 2 in one step into the
+  flash, but the RBL ignores the page settings, so I have to
+  burn the UBL Header to a page 0 and the spl code to
+  a page 0 ... :-(
+- If we make the nand read/write functions in the RBL equal to
+  the functions in u-boot (as I have no RBL code, it is only
+  possible in u-boot), we could burn the complete image in
+  one step ... that would be nice ...
diff --git a/doc/README.omap3 b/doc/README.omap3
index 2a3f46b63c..0a37de0c76 100644
--- a/doc/README.omap3
+++ b/doc/README.omap3
@@ -68,6 +68,11 @@ make
 make cm_t35_config
 make
 
+* BlueLYNX-X:
+
+make omap3_mvblx_config
+make
+
 Custom commands
 ===============