From a3554a151aa9c9ab2affd289458269273b08dfcf Mon Sep 17 00:00:00 2001 From: Hiago De Franco Date: Wed, 27 Sep 2023 13:22:25 -0300 Subject: [PATCH] toradex: colibri_imx7: Enable nand/emmc detection and set boot variant Add detection of eMMC vs NAND devices on the Colibri iMX7 board. A GPIO is configured to detect the presence of an on-board resistor that is configured differently based on the flash memory used. Depending on the detection result, the 'variant' environment variable is set to '-emmc' or cleared, indicating the type of storage device. This enhancement improves variant detection during system initialization through USB recovery mode, where U-Boot is loaded directly to RAM. This allows variant detection for an accurate device tree selection. Submitted [https://lore.kernel.org/u-boot/20231002115749.15160-1-hiagofranco@gmail.com/] Signed-off-by: Hiago De Franco --- board/toradex/colibri_imx7/colibri_imx7.c | 24 +++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/board/toradex/colibri_imx7/colibri_imx7.c b/board/toradex/colibri_imx7/colibri_imx7.c index 119e67b47f..f0356af008 100644 --- a/board/toradex/colibri_imx7/colibri_imx7.c +++ b/board/toradex/colibri_imx7/colibri_imx7.c @@ -53,6 +53,11 @@ DECLARE_GLOBAL_DATA_PTR; #define USB_CDET_GPIO IMX_GPIO_NR(7, 14) +#define FLASH_DETECTION_CTRL (PAD_CTL_HYS | PAD_CTL_PUE) +#define FLASH_DET_GPIO IMX_GPIO_NR(6, 11) + +static bool is_emmc; + int dram_init(void) { gd->ram_size = get_ram_size((void *)PHYS_SDRAM, imx_ddr_size()); @@ -60,6 +65,10 @@ int dram_init(void) return 0; } +static iomux_v3_cfg_t const flash_detection_pads[] = { + MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(FLASH_DETECTION_CTRL), +}; + static iomux_v3_cfg_t const uart1_pads[] = { MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), @@ -183,6 +192,16 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + /* + * Enable GPIO on NAND_WE_B/eMMC_RST with 100k pull-down. eMMC_RST + * is pulled high with 4.7k for eMMC devices. This allows to reliably + * detect eMMC/NAND flash + */ + imx_iomux_v3_setup_multiple_pads(flash_detection_pads, ARRAY_SIZE(flash_detection_pads)); + gpio_request(FLASH_DET_GPIO, "flash-detection-gpio"); + is_emmc = gpio_get_value(FLASH_DET_GPIO); + gpio_free(FLASH_DET_GPIO); + #ifdef CONFIG_FEC_MXC setup_fec(); #endif @@ -348,6 +367,11 @@ int board_late_init(void) env_set("bootcmd", "sdp 0"); } #endif + if (is_emmc) + env_set("variant", "-emmc"); + else + env_set("variant", ""); + return 0; } #endif /* CONFIG_BOARD_LATE_INIT */ -- 2.40.1