| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 15a3adfe75937c9e4e0e48f0ed40dd39a0e526e2.
The backport of [1] relies on having [2] also backported. Having only
one of the two results in a bogus hw->timing1 setting.
If only [2] is backportet the 16 bit register value likely underflows
resulting in a busy_wait_timeout of 0.
Or if only [1] is applied the value likely overflows with chances of
having last 16 LSBs all 0 which would then result in a
busy_wait_timeout of 0 too.
Both cases may lead to NAND data corruption, e.g. on a Colibri iMX7
setup this has been seen.
[1] commit 0fddf9ad06fd ("mtd: rawnand: gpmi: Set WAIT_FOR_READY
timeout based on program/erase times")
[2] commit 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy
timeout setting")
Upstream-Status: Submitted [https://lore.kernel.org/all/20240207174911.870822-1-max.oss.09@gmail.com/]
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
commit 0fddf9ad06fd9f439f137139861556671673e31c upstream.
06781a5026350 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026350 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b1206122069aa ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 71c76f56b97c15d367f0855bbf2127029bdabecc which is
commit 06781a5026350cde699d2d10c9914a25c1524f45 upstream.
It is reported to cause data loss, so revert it to prevent that from
happening for users of this driver.
Reported-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20220701110341.3094023-1-s.hauer@pengutronix.de/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06781a5026350cde699d2d10c9914a25c1524f45 upstream.
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b1206122069aa ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2970bf5a32f079e1e9197411db4fe9faccb1503a ]
Set the controller registers according to the real clock rate. The
controller registers configuration (setup, hold, timeout, ... cycles)
depends on the clock rate of the GPMI. Using the real rate instead of
the ideal one, avoids that this inaccuracy (required_rate - real_rate)
affects the registers setting.
This patch has been tested on two custom boards with i.MX28 and i.MX6
SOCs:
- i.MX28:
required rate 100MHz, real rate 99.3MHz
- i.MX6
required rate 100MHz, real rate 99MHz
Fixes: b1206122069a ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9161f365c91614e5a3f5c6dcc44c3b1b33bc59c0 upstream.
If gpmi_nfc_apply_timings() fails, the PM runtime usage counter must be
dropped.
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: f53d4c109a66 ("mtd: rawnand: gpmi: Add ERR007117 protection for nfc_apply_timings")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220125081619.6286-1-ceggers@arri.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa1baa0e6c1aa4872e481dce4fc7fd6f3dd8496b upstream.
There is no need to explicitly set the default gpmi clock rate during
boot for the i.MX 6 since this is done during nand_detect anyway.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-1-ceggers@arri.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f53d4c109a666bf1a4883b45d546fba079258717 upstream.
gpmi_io clock needs to be gated off when changing the parent/dividers of
enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX).
Otherwise this rate change can lead to an unresponsive GPMI core which
results in DMA timeouts and failed driver probe:
[ 4.072318] gpmi-nand 112000.gpmi-nand: DMA timeout, last DMA
...
[ 4.370355] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -110
...
[ 4.375988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.381524] gpmi-nand 112000.gpmi-nand: Error in ECC-based read: -22
[ 4.387988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.393535] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
...
Other than stated in i.MX 6 erratum ERR007117, it should be sufficient
to gate only gpmi_io because all other bch/nand clocks are derived from
different clock roots.
The i.MX6 reference manuals state that changing clock muxers can cause
glitches but are silent about changing dividers. But tests showed that
these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn,
the manual guarantees that no glitches can happen when changing
dividers.
Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 076de75de1e53160e9b099f75872c1f9adf41a0b ]
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Fixes: 4d02423e9afe6 ("mtd: nand: gpmi: Fix gpmi_nand_init() error path")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7671edeb193910482a9b0c22cd32176e7de7b2ed ]
To get better performance, current gpmi driver collected and chained all
small DMA transfers in gpmi_nfc_exec_op, the whole chain triggered and
wait for complete at the end.
But some random DMA timeout found in this new driver, with the help of
ftrace, we found the root cause is as follows:
Take gpmi_ecc_read_page() as an example, gpmi_nfc_exec_op collected 6
DMA transfers and the DMA chain triggered at the end. It waits for bch
completion and check jiffies if it's timeout. The typical function graph
shown below,
63.216351 | 1) | gpmi_ecc_read_page() {
63.216352 | 1) 0.750 us | gpmi_bch_layout_std();
63.216354 | 1) | gpmi_nfc_exec_op() {
63.216355 | 1) | gpmi_chain_command() {
63.216356 | 1) | mxs_dma_prep_slave_sg() {
63.216357 | 1) | /* mxs chan ccw idx: 0 */
63.216358 | 1) 1.750 us | }
63.216359 | 1) | mxs_dma_prep_slave_sg() {
63.216360 | 1) | /* mxs chan ccw idx: 1 */
63.216361 | 1) 2.000 us | }
63.216361 | 1) 6.500 us | }
63.216362 | 1) | gpmi_chain_command() {
63.216363 | 1) | mxs_dma_prep_slave_sg() {
63.216364 | 1) | /* mxs chan ccw idx: 2 */
63.216365 | 1) 1.750 us | }
63.216366 | 1) | mxs_dma_prep_slave_sg() {
63.216367 | 1) | /* mxs chan ccw idx: 3 */
63.216367 | 1) 1.750 us | }
63.216368 | 1) 5.875 us | }
63.216369 | 1) | /* gpmi_chain_wait_ready */
63.216370 | 1) | mxs_dma_prep_slave_sg() {
63.216372 | 1) | /* mxs chan ccw idx: 4 */
63.216373 | 1) 3.000 us | }
63.216374 | 1) | /* gpmi_chain_data_read */
63.216376 | 1) | mxs_dma_prep_slave_sg() {
63.216377 | 1) | /* mxs chan ccw idx: 5 */
63.216378 | 1) 2.000 us | }
63.216379 | 1) 1.125 us | mxs_dma_tx_submit();
63.216381 | 1) 1.000 us | mxs_dma_enable_chan();
63.216712 | 0) 2.625 us | mxs_dma_int_handler();
63.216717 | 0) 4.250 us | bch_irq();
63.216723 | 0) 1.250 us | mxs_dma_tasklet();
63.216723 | 1) | /* jiffies left 250 */
63.216725 | 1) ! 372.000 us | }
63.216726 | 1) 2.625 us | gpmi_count_bitflips();
63.216730 | 1) ! 379.125 us | }
but it's not gurantee that bch irq handled always after dma irq handled,
sometimes bch_irq comes first and gpmi_nfc_exec_op won't wait anymore,
another gpmi_nfc_exec_op may get invoked before last DMA chain IRQ
handled, this messed up the next DMA chain and causes DMA timeout. Check
the trace log when issue happened.
63.218923 | 1) | gpmi_ecc_read_page() {
63.218924 | 1) 0.625 us | gpmi_bch_layout_std();
63.218926 | 1) | gpmi_nfc_exec_op() {
63.218927 | 1) | gpmi_chain_command() {
63.218928 | 1) | mxs_dma_prep_slave_sg() {
63.218929 | 1) | /* mxs chan ccw idx: 0 */
63.218929 | 1) 1.625 us | }
63.218931 | 1) | mxs_dma_prep_slave_sg() {
63.218931 | 1) | /* mxs chan ccw idx: 1 */
63.218932 | 1) 1.750 us | }
63.218933 | 1) 5.875 us | }
63.218934 | 1) | gpmi_chain_command() {
63.218934 | 1) | mxs_dma_prep_slave_sg() {
63.218935 | 1) | /* mxs chan ccw idx: 2 */
63.218936 | 1) 1.875 us | }
63.218937 | 1) | mxs_dma_prep_slave_sg() {
63.218938 | 1) | /* mxs chan ccw idx: 3 */
63.218939 | 1) 1.625 us | }
63.218939 | 1) 5.875 us | }
63.218940 | 1) | /* gpmi_chain_wait_ready */
63.218941 | 1) | mxs_dma_prep_slave_sg() {
63.218942 | 1) | /* mxs chan ccw idx: 4 */
63.218942 | 1) 1.625 us | }
63.218943 | 1) | /* gpmi_chain_data_read */
63.218944 | 1) | mxs_dma_prep_slave_sg() {
63.218945 | 1) | /* mxs chan ccw idx: 5 */
63.218947 | 1) 2.375 us | }
63.218948 | 1) 0.625 us | mxs_dma_tx_submit();
63.218949 | 1) 1.000 us | mxs_dma_enable_chan();
63.219276 | 0) 5.125 us | bch_irq(); <----
63.219283 | 1) | /* jiffies left 250 */
63.219285 | 1) ! 358.625 us | }
63.219286 | 1) 2.750 us | gpmi_count_bitflips();
63.219289 | 1) ! 366.000 us | }
63.219290 | 1) | gpmi_ecc_read_page() {
63.219291 | 1) 0.750 us | gpmi_bch_layout_std();
63.219293 | 1) | gpmi_nfc_exec_op() {
63.219294 | 1) | gpmi_chain_command() {
63.219295 | 1) | mxs_dma_prep_slave_sg() {
63.219295 | 0) 1.875 us | mxs_dma_int_handler(); <----
63.219296 | 1) | /* mxs chan ccw idx: 6 */
63.219297 | 1) 2.250 us | }
63.219298 | 1) | mxs_dma_prep_slave_sg() {
63.219298 | 0) 1.000 us | mxs_dma_tasklet();
63.219299 | 1) | /* mxs chan ccw idx: 0 */
63.219300 | 1) 1.625 us | }
63.219300 | 1) 6.375 us | }
63.219301 | 1) | gpmi_chain_command() {
63.219302 | 1) | mxs_dma_prep_slave_sg() {
63.219303 | 1) | /* mxs chan ccw idx: 1 */
63.219304 | 1) 1.625 us | }
63.219305 | 1) | mxs_dma_prep_slave_sg() {
63.219306 | 1) | /* mxs chan ccw idx: 2 */
63.219306 | 1) 1.875 us | }
63.219307 | 1) 6.000 us | }
63.219308 | 1) | /* gpmi_chain_wait_ready */
63.219308 | 1) | mxs_dma_prep_slave_sg() {
63.219309 | 1) | /* mxs chan ccw idx: 3 */
63.219310 | 1) 2.000 us | }
63.219311 | 1) | /* gpmi_chain_data_read */
63.219312 | 1) | mxs_dma_prep_slave_sg() {
63.219313 | 1) | /* mxs chan ccw idx: 4 */
63.219314 | 1) 1.750 us | }
63.219315 | 1) 0.625 us | mxs_dma_tx_submit();
63.219316 | 1) 0.875 us | mxs_dma_enable_chan();
64.224227 | 1) | /* jiffies left 0 */
In the first gpmi_nfc_exec_op, bch_irq comes first and gpmi_nfc_exec_op
exits, but DMA IRQ still not happened yet until the middle of following
gpmi_nfc_exec_op, the first DMA transfer index get messed and DMA get
timeout.
To fix the issue, when there is bch ops in DMA chain, the
gpmi_nfc_exec_op should wait for both completions rather than bch
completion only.
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201209035104.22679-3-han.xu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b391c7f2e863985668d705f525af3ceb55bc800 ]
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. If runtime of the device has
error or device is in inaccessible state(or other error state),
resume operation will fail. If we do not call put operation to
decrease the reference, it will result in reference leak in
the two functions(gpmi_init and gpmi_nfc_exec_op). Moreover,
this device cannot enter the idle state and always stay busy or
other non-idle state later. So we fixed it through adding
pm_runtime_put_noidle.
Fixes: 5bc6bb603b4d0 ("mtd: rawnand: gpmi: Fix suspend/resume problem")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201107110552.1568742-1-zhangqilong3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 550e68ea36a6671a96576c0531685ce6e6c0d19d ]
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522095139.19653-1-dinghao.liu@zju.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d70486668cdf51b14a50425ab45fc18677a167b2 upstream.
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bc6bb603b4d0c8802af75e4932232683ab2d761 upstream.
On system resume, the gpmi clock must be enabled before accessing gpmi
block. Without this, resume causes something like
[ 661.348790] gpmi_reset_block(5cbb0f7e): module reset timeout
[ 661.348889] gpmi-nand 1806000.gpmi-nand: Error setting GPMI : -110
[ 661.348928] PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -110
[ 661.348961] PM: Device 1806000.gpmi-nand failed to resume: error -110
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable block_size is being assigned to itself and to
geo->ecc_chunk_size. Clean up the double assignment by removing
the assignment to itself.
Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The gpmi driver performance suffers from NAND operations being split
in multiple small DMA transfers. This has been forced by the NAND layer
in the former days, but now with exec_op we can use the controller as
intended.
With this patch gpmi_nfc_exec_op becomes the main entry point to NAND
operations. Here all instructions are collected and chained as separate
DMA transfers. In the end whole chain is fired and waited to be
finished. gpmi_nfc_exec_op only does the hardware operations, bad block
marker swapping and buffer scrambling is done by the callers. It's worth
noting that the nand_*_op functions always take the buffer lengths for
the data that the NAND chip actually transfers. When doing BCH we have
to calculate the net data size from the raw data size in some places.
This patch has been tested with 2048/64 and 2048/128 byte NAND on
i.MX6q. mtd_oobtest, mtd_subpagetest and mtd_speedtest run without
errors. nandbiterrs, nandpagetest and nandsubpagetest userspace tests
from mtdutils run without errors and UBIFS can successfully be mounted.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The mxs dma driver uses the flags parameter in dmaengine_prep_slave_sg() for
custom flags, but still uses the dmaengine specific names of the flags.
Do a little bit better and at least give the flag a custom name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The mxs dma driver can do PIO transfers. A pointer to the PIO words
to transfer is passed in the struct scatterlist * argument of
dmaengine_prep_slave_sg(). It's quite ugly and non obvious to cast
u32 * to struct scatterlist * each time when calling
dmaengine_prep_slave_sg(), so add a static inline wrapper function
to be called by the user along with a description what is going on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The DMA_PREP_INTERRUPT flag is no longer needed by the mxs DMA driver,
drop it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The gpmi driver aggressively en/disables the clocks between operations
which has significant performance cost. Use runtime PM to get rid of
this bottleneck.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The i.MX23 specific option read code is called right after nand_scan. We
can rely on the NAND core having disabled the chipselect, so there's no
point in restoring the original chip select after NAND operations. Drop
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
gpmi_ecc_read_page_data uses the page parameter only for a debug printf,
so we can drop the parameter and the debug printf. Moving the oob
delivery from gpmi_ecc_read_page_data to gpmi_ecc_read_page makes the
oob_required parameter unnecessary aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The driver calls nand_read_page_op without a buffer passed and then
calls chip->legacy.read_buf to read the buffer afterwards which is
the same as passing the buffer nand_read_page_op in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
this->page_buffer_virt and this->payload_virt are always set to the same
value, so drop the former and just use the latter. Same for
this->page_buffer_virt and this->payload_virt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This moves the whole driver into a single C file. The filename gpmi-lib
implies that it implements library functions, but in fact there are
several cases where functions in gpmi-lib.c call back into functions in
gpmi-nand.c. With this one has to constantly jump between those two
files, so moving it into a single file improves readability, even when
the file gets quite large.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
The target size can now be returned by nanddev_get_targetsize(). Get
rid of the chip->chipsize field and use this helper instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
We plan to move cache related fields to a pagecache struct in nand_chip
but some drivers access ->pagebuf directly to invalidate the cache
before they start using ->data_buf.
Let's provide an helper that returns a pointer to ->data_buf after
invalidating the cache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
Introduce a GPMI_IS_MXS() macro to take into account the cases
when mx23 or mx28 are used, which helps readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
We try to force NAND controller drivers to properly separate the NAND
controller object from the NAND chip one, so let's deprecate the dummy
controller object embedded in nand_chip to encourage them to create
their own instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
->setup_data_interface() is a controller specific method and should
thus be placed in nand_controller_ops.
In order to make that work with controllers that support keeping
pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to
inform the core it should skip the timings selection step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Now that the CS line to be selected is passed to ->exec_op() and
stored in chip->cur_cs and after patching all drivers implementing
->exec_op() to stop implementing this method, we can deprecate it by
moving it to the nand_legacy structure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add a wrapper to prevent drivers and core code from directly calling
the ->select_chip hook which we are about to deprecate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Those hooks have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should
have been an MTD driver (docg4), or it was not properly implementing
the OOB read/write request or had a weird layout where BBM are trashed.
In any case, we should discourage people from overloading those
methods and encourage them to fix their driver instead.
Move the ->block_{bad,markbad}() hooks to the nand_legacy struct to
make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
All those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->dev_ready() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmd_ctrl() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->block_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->select_chip() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_release()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Let's make the raw NAND API consistent by patching all helpers to take
a nand_chip object instead of an mtd_info one.
We start with nand_scan().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
None of the existing drivers are overloading the ->scan_bbt() method,
let's get rid of it and replace calls to ->scan_bbt() by
nand_create_bbt() ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
