summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2016-11-21apalis-tk1: adjust pin muxing for v1.1 hwMarcel Ziswiler
Configure Apalis MMC1 D6 GPIO on SDMMC3_CLK_LB_IN as reserved function without any pull-up/down. Configure GPIO_PV2 as SD1_CD# according to latest V1.1 HW. Leave SDMMC3_CLK_LB_OUT muxed as SDMMC3 with output driver enabled aka not tristated and input driver enabled as well as it features some magic properties even though the external loopback is disabled and the internal loopback used as per SDMMC_VENDOR_MISC_CNTRL_0 register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM! This pin is now a not-connect on V1.1 HW in order to avoid any interference. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: temp alert pull-upMarcel Ziswiler
Pull-up GPIO_PI6 connected to TMP451's ALERT#/THERM2#. While at it improve some comments. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: fix pcie clock and reset not conforming to specificationMarcel Ziswiler
Fix PCIe clock and reset not conforming to specification by moving PCIe reset handling including the PLX PEX 8605 errata 5 workaround from the board platform data into the right places timing wise in the PCIe driver itself. Also add a kernel command line argument to allow using the Apalis GPIO7 as a regular GPIO rather than for above mentioned PLX PEX 8605 workaround: pex_perst=0 Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com> (cherry picked from tegra-next commit a2f63805703b43d55d91ae17f10d0049bf0f625e)
2016-11-21apalis-tk1: configure IPv6 SIT driver as moduleStefan Agner
SIT tunnels (IPv6 over IPv4) are not often used hence configure the driver as a module. This also gets rid of the extra network interface sit0 by default. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2016-11-21apalis-tk1: integrate adv7280-m, ap1302, ov5640 and tc358743 supportMarcel Ziswiler
Integrate SoC camera support for the following CSI-2 codecs/sensors: - Analog Devices ADV7280-M, analog camera decoder with deinterlacer, PAL/NTSC@60fps - ON Semiconductor (formerly Aptina) AP1302 ISP + AR1820 image sensor, 13Mpx, 1080p@30fps - OmniVision OV5640, 5Mpx sensor, 1080p@30fps - Toshiba TC358743 HDMI to CSI-2 bridge, 1080p@60fps Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21media: support for second single-lane decoder (ADV7280M)Wojciech Bieganski
Connected to CSI CIL-E. Cameras doesn't work simultaneously. Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21media: tc358743: update hdmi to csi-2 driverTomasz Gorochowik
A major part of the driver has been rewritten in order to avoid writing binary blobs to the chip. This version also adds support for more video modes. Input video modes supported: - 1920x1080 @ 60 - 1280x1024 @ 75 - 1280x720 @ 60 - 1024x768 @ 75 - 800x600 @ 75 - 640x480 @ 75 Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21ADV7280M video decoder with deinterlacer supportWojciech Bieganski
known issues: - decoder outputs PAL (720x576), but the image looks fine only when streamed in 640x576 mode, - vertical synchronisation glitches, - setting queue-size in gstreamer greater than 1 results in blinking image, - every start of streaming requires reloading of the modules Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21TC358743 HDMI to CSI-2 bridge supportWojciech Bieganski
known issues: - HDMI input works only in 640x480 mode, 720p only in test pattern mode, any 4-lane mode doesn't work - set HDMI transmitter to VGA mode before starting the stream Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21OV5640 camera supportWojciech Bieganski
known issues: - works only in 1080p mode, - vertical synchronisation glitches, - setting queue-size in gstreamer greater than 1 results in blinking image - every start of streaming requires reloading of the modules Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21AP1302 from ON Semiconductor support addedMarcel Ziswiler
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: re-add soc camera platform dataMarcel Ziswiler
Re-add SoC camera platform data from Ardbeg/Jetson TK1 board files. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: integrate optional edp supportMarcel Ziswiler
Integrate optional eDP support (e.g. uncomment define of APALIS_TK1_EDP as found in the platform data header file. Tested using a prototype Apalis TK1 mezzanine connecting to a Samsung LTN156FL02-L01 panel featuring a 4K aka UHD resolution of 3840 by 2160. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: clean-up board platform data header fileMarcel Ziswiler
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: clean-up board platform dataMarcel Ziswiler
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: clean-up defconfigMarcel Ziswiler
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: select dp pinmux function for dp_hpdMarcel Ziswiler
Select dp pinmux function for Apalis GPIO2 aka DP_HPD to allow it to be used as eDP hot-plug detect. From user space customer may still configure and use it as a regular GPIO if desired. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: remove gpio functionality from dp_hpd and gpio_pff2 pinsMarcel Ziswiler
Remove default GPIO functionality from Apalis GPIO1 aka GPIO_PFF2 and Apalis GPIO2 aka DP_HPD as if later trying to use resp. pins as special function (e.g. the former for eDP hot-plug detect and the later for SATA data activity) there is currently no sane way of removing the GPIO functionality again. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis-tk1: add comment concerning ssp1 on usb2p0 functionality being tbdMarcel Ziswiler
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-11-21apalis_tk1: Enable UART4Dominik Sliwa
Uncomment UART4 device tree node and enable support in machfile Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2016-11-21apalis-tk1: fix cl-dvfs and soctherm to unlock full performanceMarcel Ziswiler
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-09-29arm: tegra: ardbeg: fix gcc-6 compilationMarcel Ziswiler
arch/arm/mach-tegra/board-ardbeg.c: In function 'ardbeg_touch_init': arch/arm/mach-tegra/board-ardbeg.c:1159:6: error: this 'else' clause does not guard... [-Werror=misleading-indentation] } else ^~~~ arch/arm/mach-tegra/board-ardbeg.c:1161:5: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the 'else' rm31080a_ardbeg_spi_board[0].irq = ^~~~~~~~~~~~~~~~~~~~~~~~~ arch/arm/mach-tegra/board-ardbeg.c: In function 'tegra_ardbeg_late_init': arch/arm/mach-tegra/board-ardbeg.c:1470:2: error: this 'else' clause does not guard... [-Werror=misleading-indentation] else ^~~~ arch/arm/mach-tegra/board-ardbeg.c:1474:3: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the 'else' tegra_io_dpd_enable(&pexbias_io); ^~~~~~~~~~~~~~~~~~~ At top level: arch/arm/mach-tegra/board-ardbeg.c:1608:27: error: 'loki_dt_board_compat' defined but not used [-Werror=unused-const-variable=] static const char * const loki_dt_board_compat[] = { ^~~~~~~~~~~~~~~~~~~~ Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-09-29apalis_tk1: Optimized RAM settingDominik Sliwa
Optimized DVFS table for Apalis TK1 boards. Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2016-06-29arm: tegra: initial support for apalis tk1Apalis_TK1_LinuxImageV2.6Beta2_20160701Marcel Ziswiler
This patch adds support for the Toradex Apalis TK1 acomputer on module which can be used on different carrier boards. The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec. Furthermore, there is a Kinetis MK20DN512 companion micro controller for analogue, CAN and resistive touch functionality which is not yet supported. This is known to boot into either a basic Angstrom/OpenEmbedded/Yocto or L4T/JetPack Ubuntu based image. The following things are known to work to a certain extend: - analogue/digital audio - debug UART1 - DVFS power management incl. low power core migration - eMMC - gigabit Ethernet - GPIOs - HDMI (incl. HDA audio) - I2C - LVDS - PCIe - SATA - SD/MMC cards - temperature sensor - USB host ports The rest is untested. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-06-29apalis-tk1: fix backlight pwm and add 800x600 and 1024x600 lvds timingsMarcel Ziswiler
Fix the backlight PWM instance used and add 800x600 and 1024x600 LVDS panel timings. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-06-29tegra: fix dvfs gcc 5.2 build errorMarcel Ziswiler
This fixes the following GCC 5.2 built time error: arch/arm/mach-tegra/tegra_cl_dvfs.c: In function 'monitor_get': arch/arm/mach-tegra/tegra_cl_dvfs.c:372:8: error: 'v' may be used uninitialized in this function [-Werror=maybe-uninitialized] *data &= CL_DVFS_MONITOR_DATA_MASK; ^ arch/arm/mach-tegra/tegra_cl_dvfs.c:2949:6: note: 'v' was declared here u32 v, s; ^ arch/arm/mach-tegra/tegra_cl_dvfs.c: In function 'cl_dvfs_calibrate': arch/arm/mach-tegra/tegra_cl_dvfs.c:372:8: error: 'data' may be used uninitialized in this function [-Werror=maybe-uninitialized] *data &= CL_DVFS_MONITOR_DATA_MASK; ^ arch/arm/mach-tegra/tegra_cl_dvfs.c:902:11: note: 'data' was declared here u32 val, data; ^ Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Dominik Sliwa <dominik.sliwa@toradex.com>
2016-06-29tegra12_clocks.c: fix unusual comparisionMax Krummenacher
newer compilers throw the following error: arch/arm/mach-tegra/tegra12_clocks.c: In function 'tegra12_cpu_clk_init': arch/arm/mach-tegra/tegra12_clocks.c:1334:31: error: logical not is only applied to the left hand side of comparison [-Werror=logical-not-parentheses] c->state = (!is_lp_cluster() == (c->u.cpu.mode == MODE_G))? ON : OFF; Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2016-06-29ARM: 8429/1: disable GCC SRA optimizationArd Biesheuvel
While working on the 32-bit ARM port of UEFI, I noticed a strange corruption in the kernel log. The following snprintf() statement (in drivers/firmware/efi/efi.c:efi_md_typeattr_format()) snprintf(pos, size, "|%3s|%2s|%2s|%2s|%3s|%2s|%2s|%2s|%2s]", was producing the following output in the log: | | | | | |WB|WT|WC|UC] | | | | | |WB|WT|WC|UC] | | | | | |WB|WT|WC|UC] |RUN| | | | |WB|WT|WC|UC]* |RUN| | | | |WB|WT|WC|UC]* | | | | | |WB|WT|WC|UC] |RUN| | | | |WB|WT|WC|UC]* | | | | | |WB|WT|WC|UC] |RUN| | | | | | | |UC] |RUN| | | | | | | |UC] As it turns out, this is caused by incorrect code being emitted for the string() function in lib/vsprintf.c. The following code if (!(spec.flags & LEFT)) { while (len < spec.field_width--) { if (buf < end) *buf = ' '; ++buf; } } for (i = 0; i < len; ++i) { if (buf < end) *buf = *s; ++buf; ++s; } while (len < spec.field_width--) { if (buf < end) *buf = ' '; ++buf; } when called with len == 0, triggers an issue in the GCC SRA optimization pass (Scalar Replacement of Aggregates), which handles promotion of signed struct members incorrectly. This is a known but as yet unresolved issue. (https://gcc.gnu.org/bugzilla/show_bug.cgi?id=65932). In this particular case, it is causing the second while loop to be executed erroneously a single time, causing the additional space characters to be printed. So disable the optimization by passing -fno-ipa-sra. Cc: <stable@vger.kernel.org> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> (cherry picked from commit a077224fd35b2f7fbc93f14cf67074fc792fbac2)
2016-06-29ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.hBehan Webster
With compilers which follow the C99 standard (like modern versions of gcc and clang), "extern inline" does the wrong thing (emits code for an externally linkable version of the inline function). In this case using static inline and removing the NULL version of return_address in return_address.c does the right thing. Signed-off-by: Behan Webster <behanw@converseincode.com> Reviewed-by: Mark Charlebois <charlebm@gmail.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> (cherry picked from commit aeea3592a13bf12861943e44fc48f1f270941f8d)
2016-05-16arm: tegra: new dvfs update for aging factorBibek Basu
Following support added DVFS for Gauranteed freq considering aging CPU freq limit at higher temperature EDP max current limits for each SKU Bug 200195229 Change-Id: If00f3fd6b891cf366047dda331bd7ab1c15b40f7 Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/1146577 GVS: Gerrit_Virtual_Submit Reviewed-by: Winnie Hsu <whsu@nvidia.com>
2016-05-13arm: tegra: emc dvfs selection based on ddrBibek Basu
select emc evfs table based on DDR present using RAMCODE Bug 200195279 Change-Id: I7fbc693383c9e231b2c2119020eebc7bba544c6e Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/1144528 Reviewed-by: Jimmy Zhang <jimmzhang@nvidia.com> GVS: Gerrit_Virtual_Submit Reviewed-by: Winnie Hsu <whsu@nvidia.com>
2016-05-02arm: config: T124: L4T: systemd related configsNinad Malwade
Added kernel configurations to support systemd functionality boot.img size is increased by 69632 bytes Bug 1731796 Change-Id: I4209fee15843ac645600500ed8c9fc37b7ff0c04 Signed-off-by: Ninad Malwade <nmalwade@nvidia.com> Reviewed-on: http://git-master/r/1134828 Reviewed-by: Automatic_Commit_Validation_User GVS: Gerrit_Virtual_Submit Reviewed-by: Bibek Basu <bbasu@nvidia.com> Reviewed-by: Rajkumar Kasirajan <rkasirajan@nvidia.com> Reviewed-by: Matthew Pedro <mapedro@nvidia.com>
2016-01-12watchdog: enable TEGRA_WATCHDOG_ENABLE_ON_PROBEJeetesh Burman
enable TEGRA_WATCHDOG_ENABLE_ON_PROBE to set "timeout" in probe call Bug 200160105 Change-Id: Ifcef77b3229acee821c5cdd2f31e449e010b9d2f Signed-off-by: Jeetesh Burman <jburman@nvidia.com> Reviewed-on: http://git-master/r/927464 GVS: Gerrit_Virtual_Submit Reviewed-by: Bibek Basu <bbasu@nvidia.com> Reviewed-by: Matthew Pedro <mapedro@nvidia.com>
2015-09-27dts: jetson-tk1: change regulator-init-microvoltJeetesh Burman
change regulator-init-microvolt for ams-as3722. Bug 1634862 Change-Id: Ie4b9d1976fca9f8bdebfb039ef2c0337e1b55dfd Signed-off-by: Jeetesh Burman <jburman@nvidia.com> Reviewed-on: http://git-master/r/794739 Reviewed-by: Naveen Kumar Arepalli <naveenk@nvidia.com> Reviewed-by: R Raj Kumar <rrajk@nvidia.com> GVS: Gerrit_Virtual_Submit Reviewed-by: Venu Byravarasu <vbyravarasu@nvidia.com>
2015-08-25video: tegra: dc: handle tegra_dc_sync_windows errorBibek Basu
In case tegra_dc_sync_windows is interrupted by signal, return the error to caller application Bug 200090492 Change-Id: Id69fbe38d0abe0b3e71eb5a413db241ebcf0a0ae Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/784754 GVS: Gerrit_Virtual_Submit Reviewed-by: Winnie Hsu <whsu@nvidia.com>
2015-08-07AR0330: validate with V4L2 for Jetson TK1Arun Kannan
Bug 1643556 Change-Id: I7330bd3ec33e2309577c75bac79e120167b0f81e Signed-off-by: Arun Kannan <akannan@nvidia.com> Reviewed-on: http://git-master/r/748395 Reviewed-by: Winnie Hsu <whsu@nvidia.com> Tested-by: Winnie Hsu <whsu@nvidia.com>
2015-08-07arm: tegra12: disable USB_NET_RAW_IPBibek Basu
drop support for USB_NET_RAW_IP as its unused Bug 200092344 Change-Id: I085330c2ed8a83f83c027d91a03d13d1ce23e4f0 Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/780277 Reviewed-by: Automatic_Commit_Validation_User GVS: Gerrit_Virtual_Submit Reviewed-by: Matthew Pedro <mapedro@nvidia.com>
2015-08-05arm: tegra: correct dap2_sclk directionBibek Basu
dap2_sclk direction should be input to take care of the bidirectional nature of the clk for codec as master and interface as master Bug 1643925 Change-Id: Iab4f1a30edd3542fbfc0e1f53dd6ea9f604ed42f Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/778298 GVS: Gerrit_Virtual_Submit Reviewed-by: Venkat Moganty <vmoganty@nvidia.com>
2015-07-27arm64: tegra13: enable shared memory configBibek Basu
enable shared memory config Bug 1632724 Change-Id: I629eaa63ea54063dc713e21a848768378b3354a3 Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/774295 Reviewed-by: Automatic_Commit_Validation_User GVS: Gerrit_Virtual_Submit Reviewed-by: Venkat Moganty <vmoganty@nvidia.com>
2015-07-23arm: tegra: headsmp: fix tegra_with_secure_firmware access with MMU offVarun Wadekar
There are places during the CPU resume path where we access this variable with MMU off. In such scenarios we should use the physical address for this variable. This fixes the virtualisation team's issue, since they were the ones who reported it in the first place. Fix a case where the code running from iRAM was accessing the variable from DRAM instead of the one cached in iRAM. Bug 1411345 Change-Id: I9005c30329d38bae305a4a7b31ae7e2ca83e8a5d Signed-off-by: Varun Wadekar <vwadekar@nvidia.com> Reviewed-on: http://git-master/r/412540 (cherry picked from commit a0553bb8f3fa7c76c2c0a6528d0c106ee22c7a59) Reviewed-on: http://git-master/r/771679 Reviewed-by: Bibek Basu <bbasu@nvidia.com> Tested-by: Bibek Basu <bbasu@nvidia.com> GVS: Gerrit_Virtual_Submit Reviewed-by: Venkat Moganty <vmoganty@nvidia.com>
2015-07-23arm: tegra: fix secure firmware check during bootBibek Basu
psci status node should also be checked along with compatible node to enable secure fimrware Bug 200124907 Change-Id: Ieb336bc7d1cc2c68d94157222770a6da6a8dcfd1 Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/772755 GVS: Gerrit_Virtual_Submit Reviewed-by: Venkat Moganty <vmoganty@nvidia.com>
2015-07-23arm: tegra: fix debug build issueBibek Basu
Initialize uninitialized variables to get the build through Bug 1640594 Change-Id: Ia0788c5852bb8d68a79004e3f2fa1b3d2b9ca2fe Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/772239 GVS: Gerrit_Virtual_Submit Reviewed-by: Venkat Moganty <vmoganty@nvidia.com> Reviewed-by: Matthew Pedro <mapedro@nvidia.com>
2015-07-14arm: tegra12: disable CONFIG_UID_STATBibek Basu
CONFIG_UID_STAT is buggy and not needed Bug 200115637 Change-Id: I105a46e91cba63508115be6fdd1c2e49962d25e8 Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/764550 GVS: Gerrit_Virtual_Submit Reviewed-by: Venkat Moganty <vmoganty@nvidia.com>
2015-06-18Revert "mmc: sdhci: tegra: update T2T and Tap hole for VCM30T124"Jeetesh Burman
This reverts commit 28c9354b7cbade8813e0e5dbe9937300219fbeb9. Signed-off-by: Jeetesh Burman <jburman@nvidia.com> Change-Id: I4a809d75523513c939fa17a6dbeebee292aec77b Reviewed-on: http://git-master/r/759472 GVS: Gerrit_Virtual_Submit Reviewed-by: Winnie Hsu <whsu@nvidia.com>
2015-06-08watchdog: use FIQ WDT for soft lockup stack dumpRenn Wu
Using Tegra WDT to trigger FIQ when system is in soft lockup. Bug 1581432 Change-Id: I853a88a3f6e9402c978db18c5a63e903c582040a Signed-off-by: Renn Wu <rewu@nvidia.com> Reviewed-on: http://git-master/r/265871 (cherry picked from commit f115f435d471af22ddec5e9d969662f79193f846) Reviewed-on: http://git-master/r/680353 GVS: Gerrit_Virtual_Submit Reviewed-by: Bibek Basu <bbasu@nvidia.com> Reviewed-by: Winnie Hsu <whsu@nvidia.com>
2015-06-04gpu: nvgpu: gk20a: dma_alloc only if neededBibek Basu
if vpr memory is carved out, then only call dma_alloc for secure memory. Bug 200057068 Change-Id: I12557cfaa48f7db729ccab17d3151916d35ce0f1 Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/746153 GVS: Gerrit_Virtual_Submit Reviewed-by: Venkat Moganty <vmoganty@nvidia.com>
2015-05-26dts: jetson-tk1: Add AR0261 sensor supportTushar Khinvasara
Added AR0261 sensor support Bug 200089114 Signed-off-by: Tushar Khinvasara <tkhinvasara@nvidia.com> Change-Id: I8f6d6c6ea4905d9087fd6281bc8b215ec0a73fdb Reviewed-on: http://git-master/r/741716 Reviewed-by: Bibek Basu <bbasu@nvidia.com> GVS: Gerrit_Virtual_Submit Reviewed-by: Ming Wong <miwong@nvidia.com> Reviewed-by: Venkat Moganty <vmoganty@nvidia.com>
2015-05-19arm: tegra: enable dnotify config for t124Bibek Basu
Enable CONFIG_DNOTIFY for L4T kernel config Bug 1627091 Bug 200097847 Change-Id: I30d53089df825a776f03e1f0f08f1d6d8b1c9bb0 Signed-off-by: Bibek Basu <bbasu@nvidia.com> Reviewed-on: http://git-master/r/741517 Reviewed-by: Automatic_Commit_Validation_User GVS: Gerrit_Virtual_Submit Reviewed-by: Matthew Pedro <mapedro@nvidia.com> Reviewed-by: Venkat Moganty <vmoganty@nvidia.com>
2015-05-14arm64: mm: Add __clean_dcache_louisKrishna Reddy
This allows perform L1 cache clean alone. Bug 200077334 Change-Id: I776de6e6726862e330b626fd19f8ae8f70055538 Signed-off-by: Krishna Reddy <vdumpa@nvidia.com> Reviewed-on: http://git-master/r/742254 GVS: Gerrit_Virtual_Submit Reviewed-by: Bibek Basu <bbasu@nvidia.com>
2015-05-14arm: mm: Add v7_clean_kern_cache_louisKrishna Reddy
This allows perform L1 cache clean alone. Bug 200077334 Change-Id: I7a6106ed53755df33e09e3fa32a9e2524eb98649 Signed-off-by: Krishna Reddy <vdumpa@nvidia.com> Reviewed-on: http://git-master/r/742252 GVS: Gerrit_Virtual_Submit Reviewed-by: Bibek Basu <bbasu@nvidia.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-01 17:50:56 +0000