| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit 55815f70147dcfa3ead5738fd56d3574e2e3c1c2 upstream.
We already use them for openat() and friends, but fstat() also wants to
be able to use O_PATH file descriptors. This should make it more
directly comparable to the O_SEARCH of Solaris.
Note that you could already do the same thing with "fstatat()" and an
empty path, but just doing "fstat()" directly is simpler and faster, so
there is no reason not to just allow it directly.
See also commit 332a2e1244bd, which did the same thing for fchdir, for
the same reasons.
Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e994defb7b6813ba6fa7a2a36e86d2455ad1dc35 upstream.
Use the *_light() versions that properly avoid doing the file user count
updates when they are unnecessary.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8335eafc2859e1a26282bef7c3d19f3d68868b8a upstream.
After calling into the lower filesystem to do a rename, the lower target
inode's attributes were not copied up to the eCryptfs target inode. This
resulted in the eCryptfs target inode staying around, rather than being
evicted, because i_nlink was not updated for the eCryptfs inode. This
also meant that eCryptfs didn't do the final iput() on the lower target
inode so it stayed around, as well. This would result in a failure to
free up space occupied by the target file in the rename() operation.
Both target inodes would eventually be evicted when the eCryptfs
filesystem was unmounted.
This patch calls fsstack_copy_attr_all() after the lower filesystem
does its ->rename() so that important inode attributes, such as i_nlink,
are updated at the eCryptfs layer. ecryptfs_evict_inode() is now called
and eCryptfs can drop its final reference on the lower inode.
http://launchpad.net/bugs/561129
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 610bd7da160f76f1644ecb4cd7f39511b49a22cc upstream.
We noticed a plymouth bug on Fedora 18, and I then
noticed this stupid thinko, fixing it fixed the problem
with plymouth.
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 985f61f7ee647ad570c05eab0b74915da2ac8e19 upstream.
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=54471
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ecd67955fd4c8e66e4df312098989d5fa7da624c upstream.
No functional change, but re-order the cases so they
evaluate properly due to the way the DCE macros work.
Noticed by kallisti5 on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 26fe45a0a76f165425f332a5aaa298f149f9db22 upstream.
Selecting ATOM_PPLL_INVALID should be equivalent as the
DCPLL or PPLL0 are already programmed for the DISPCLK, but
the preferred method is to always specify the PLL selected.
SetPixelClock will check the parameters and skip the
programming if the PLL is already set up.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 17c60c6b763cb5b83b0185e7d38d01d18e55a05a upstream.
This can also appear as 0x9192. Reported in bugzilla and confirmed with the
board documentation for these boards.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42970
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5e1782d224c79b26ab7d5c31e3f87657000714fb upstream.
Testing and works with the -modesetting driver,
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3737e2be505d872bf2b3c1cd4151b2d2b413d7b5 upstream.
The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right. This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.
Signed-off-by: Matteo Frigo <athena@fftw.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 73d7c119255615a26070f9d6cdb722a166a29015 upstream.
twl4030_madc_conversion uses do_avg and type structure elements of
twl4030_madc_request. Initialize structure to avoid random operation.
Fix for: Coverity CID 200794 Uninitialized scalar variable.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3d037774b42ed677f699b1dce7d548d55f4e4c2b upstream.
There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.
Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.
qTD1 --> qTD2 --> Dummy
To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed. The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt. If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error. Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit abf02cfc179bb4bd30d05f582d61b3b8f429b813 upstream.
64bit arches have a buggy r8712u driver, let's fix it.
skb->tail must be set properly or network stack behavior is undefined.
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=847525
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=45071
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Jones <davej@redhat.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f08dea734844aa42ec57c229b0b73b3d7d21f810 upstream.
The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application. This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction. The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.
Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00. I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.
Reported-by: Florian Wöhrl <fw@woehrl.biz>
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 07dc59f0988cb54fd87bd373b3b27eb2401dd811 upstream.
snd_hda_codec_reset() calls restore_pincfgs() where the codec is
powered up again, which eventually tries to resume and initialize via
the callbacks of the codec. However, it's the place just after codec
free callback, thus no codec callbacks should be called after that.
On a codec like CS4206, it results in Oops due to the access in init
callback.
This patch fixes the issue by clearing the codec callbacks properly
after freeing codec.
Reported-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2b2040af0b64cd93e5d4df2494c4486cf604090d upstream.
get_user may fail to load from the provided __user address due to an
unhandled fault generated by the access.
In the case of the undefined instruction trap, this results in failure
to load the faulting instruction, in which case we should send SIGILL to
the task rather than continue with potentially uninitialised data.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 70b0476a2394de4f4e32e0b67288d80ff71ca963 upstream.
'make dtbs' in a clean tree will try running the dtc before actually
building it. Make these rules depend upon the scripts to build it.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f39c1bfb5a03e2d255451bff05be0d7255298fa4 upstream.
Commit 43cedbf0e8dfb9c5610eb7985d5f21263e313802 (SUNRPC: Ensure that
we grab the XPRT_LOCK before calling xprt_alloc_slot) is causing
hangs in the case of NFS over UDP mounts.
Since neither the UDP or the RDMA transport mechanism use dynamic slot
allocation, we can skip grabbing the socket lock for those transports.
Add a new rpc_xprt_op to allow switching between the TCP and UDP/RDMA
case.
Note that the NFSv4.1 back channel assigns the slot directly
through rpc_run_bc_task, so we can ignore that case.
Reported-by: Dick Streefland <dick.streefland@altium.nl>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 01913b49cf1dc6409a07dd2a4cc6af2e77f3c410 upstream.
If decode_getfh failed, nfs4_xdr_dec_open would return 0 since the last
decode_* call must have succeeded.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 60e233a56609fd963c59e99bd75c663d63fa91b6 upstream.
Fengguang Wu <fengguang.wu@intel.com> writes:
> After the __devinit* removal series, I can still get kernel panic in
> show_uevent(). So there are more sources of bug..
>
> Debug patch:
>
> @@ -343,8 +343,11 @@ static ssize_t show_uevent(struct device
> goto out;
>
> /* copy keys to file */
> - for (i = 0; i < env->envp_idx; i++)
> + dev_err(dev, "uevent %d env[%d]: %s/.../%s\n", env->buflen, env->envp_idx, top_kobj->name, dev->kobj.name);
> + for (i = 0; i < env->envp_idx; i++) {
> + printk(KERN_ERR "uevent %d env[%d]: %s\n", (int)count, i, env->envp[i]);
> count += sprintf(&buf[count], "%s\n", env->envp[i]);
> + }
>
> Oops message, the env[] is again not properly initilized:
>
> [ 44.068623] input input0: uevent 61 env[805306368]: input0/.../input0
> [ 44.069552] uevent 0 env[0]: (null)
This is a completely different CONFIG_HOTPLUG problem, only
demonstrating another reason why CONFIG_HOTPLUG should go away. I had a
hard time trying to disable it anyway ;-)
The problem this time is lots of code assuming that a call to
add_uevent_var() will guarantee that env->buflen > 0. This is not true
if CONFIG_HOTPLUG is unset. So things like this end up overwriting
env->envp_idx because the array index is -1:
if (add_uevent_var(env, "MODALIAS="))
return -ENOMEM;
len = input_print_modalias(&env->buf[env->buflen - 1],
sizeof(env->buf) - env->buflen,
dev, 0);
Don't know what the best action is, given that there seem to be a *lot*
of this around the kernel. This patch "fixes" the problem for me, but I
don't know if it can be considered an appropriate fix.
[ It is the correct fix for now, for 3.7 forcing CONFIG_HOTPLUG to
always be on is the longterm fix, but it's too late for 3.6 and older
kernels to resolve this that way - gregkh ]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 92fc7a8b0f20bdb243c706daf42658e8e0cd2ef0 upstream.
This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device. The device doesn't like to be asked for
its interface strings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: adam ? <adam3337@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 26a538b9ea2a3ee10dafc0068f0560dfd7b7ba37 upstream.
This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>. It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit dafc4f7be1a556ca3868d343c00127728b397068 upstream.
Commit b69cc672052540 added support for the E-861. After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.
Compiled, but only actually tested on the E-861 and C-867.
Signed-off-by: Éric Piel <piel@delmic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d90c92fee89ccd75ef2646f3bde0b4c0450666c3 upstream.
This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.
The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.
The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 7be0670f7b9198382938a03ff3db7f47ef6b4780 upstream.
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: deleted code in imx_setup_ufcr() refers to
sport->clk not sport->clk_per]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 9ec1882df244c4ee1baa692676fef5e8b0f5487d upstream.
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 296365781903226a3fb8758901eaeec09d2798e4 upstream.
For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.
Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.
[ balbi@ti.com: slight improvement to commit log ]
This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.
Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 upstream.
This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.
If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.
As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.
For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.
If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.
Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).
This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.
This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset. The kernels will need to
contain both commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd37df08aaa599aa361a9f8b836ba98e554 "usb: Add support for root hub
port status CAS". The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream.
My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.
I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.
This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 052c7f9ffb0e95843e75448d02664459253f9ff8 upstream.
The intent was to test whether the flag was set.
This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474f0db3a4d940cae1423783edd966027 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e95829f474f0db3a4d940cae1423783edd966027 upstream.
The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS. If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system. Some BIOS will work around this, but not all.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown. The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.
Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names. One example
is Compulab's mini-desktop, the Intense-PC. Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.
The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 6d7d9798ad5c97ee4e911dd070dc12dc5ae55bd0 upstream.
This patch fixes a race condition that results in memory
corruption when using cleancache.
The race exists between the zcache shrinker handler,
shrink_zcache_memory() and cleancache_get_page().
In most cases, the shrinker will both evict a zbpg
from its buddy list and flush it from tmem before a
cleancache_get_page() occurs on that page. A subsequent
cleancache_get_page() will fail in the tmem layer.
In the rare case that two occur together and the
cleancache_get_page() path gets through the tmem
layer before the shrinker path can flush tmem,
zbud_decompress() does a check to see if the zbpg is a
"zombie", i.e. not on a buddy list, which means the shrinker
is in the process of reclaiming it. If the zbpg is a zombie,
zbud_decompress() returns -EINVAL.
However, this return code is being ignored by the caller,
zcache_pampd_get_data_and_free(), which results in the
caller of cleancache_get_page() thinking that the page has
been properly retrieved when it has not.
This patch modifies zcache_pampd_get_data_and_free() to
convey the failure up the stack so that the caller of
cleancache_get_page() knows the page retrieval failed.
This needs to be applied to stable trees as well.
zcache-main.c was named zcache.c before v3.1, so
I'm not sure how you want to handle trees earlier
than that.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit efd5d6b03bd9c9e0df646c56fb5f4f3e25e5c1ac upstream.
On our system (ARM Cortex-M3 SOC running linux-2.6.33)
frequent crashes were observed in the rt2800usb module
because of the invalid length of the received packet (3392,
46920...). This patch adds the sanity check on the packet
legth. Also, changed WARNING to ERROR in rt2x00lib_rxdone()
so that the bad packet condition would be noticed.
The fix was tested on the latest compat-wireless-3.5.1-1-snpc.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a396e10019eaf3809b0219c966865aaafec12630 upstream.
We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 6ced58a5dbb94dbfbea1b33ca3c56d1e929cd548 upstream.
The register is 16 bits wide, not 32.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 177ef8360fabdc49ff08d2598c06e7f7a36b53e3 upstream.
This is an RT3572 based device.
Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a96874a2a92feaef607ddd3137277a788cb927a6 upstream.
With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.
The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.
There are two more registers that contains the information of the switchable
and non-switchable ports.
This patch adds the checking code for the two register so that only the
switchable ports are altered.
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 29d214576f936db627ff62afb9ef438eea18bcd2 upstream.
On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.
BugLink: http://bugs.launchpad.net/bugs/1000424
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit aa209eef3ce8419ff2926c2fa944dfbfb5afbacb upstream.
Hi,
This patch fixes a bug with driver failing to negotiate a connection.
The bug was traced to commit
203e4615ee9d9fa8d3506b9d0ef30095e4d5bc90
staging: vt6656: removed custom definitions of Ethernet packet types
In that patch, definitions in include/linux/if_ether.h replaced ones
in tether.h which had both big and little endian definitions.
include/linux/if_ether.h only refers to big endian values, cpu_to_be16
should be used for the correct endian architectures.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 61ed59ed09e6ad2b8395178ea5ad5f653bba08e3 upstream.
Don't zero out bits 15..12 of the data value in `das08jr_ao_winsn()` as
that knobbles the upper three-quarters of the output range for the
'das08jr-16-ao' board.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e6391a182865efc896cb2a8d79e07b7ac2f45b48 upstream.
The element of `das08_boards[]` for the 'das08jr-16-ao' board has the
`ai_encoding` member set to `das08_encode12`. It should be set to
`das08_encode16` same as the 'das08jr/16' board. After all, this board
has 16-bit AI resolution.
The description of the A/D LSB register at offset 0 seems incorrect in
the user manual "cio-das08jr-16-ao.pdf" as it implies that the AI
resolution is only 12 bits. The diagrams of the A/D LSB and MSB
registers show 15 data bits and a sign bit, which matches what the
software expects for the `das08_encode16` AI encoding method.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 872ece86ea5c367aa92f44689c2d01a1c767aeb3 upstream.
Apparently, am-utils is still using the legacy binary mountdata interface,
and is having trouble parsing /proc/mounts due to the 'port=' field being
incorrectly set.
The following patch should fix up the regression.
Reported-by: Marius Tolzmann <tolzmann@molgen.mpg.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c3f52af3e03013db5237e339c817beaae5ec9e3a upstream.
When the NFS_COOKIEVERF helper macro was converted into a static
inline function in commit 99fadcd764 (nfs: convert NFS_*(inode)
helpers to static inline), we broke the initialisation of the
readdir cookies, since that depended on doing a memset with an
argument of 'sizeof(NFS_COOKIEVERF(inode))' which therefore
changed from sizeof(be32 cookieverf[2]) to sizeof(be32 *).
At this point, NFS_COOKIEVERF seems to be more of an obfuscation
than a helper, so the best thing would be to just get rid of it.
Also see: https://bugzilla.kernel.org/show_bug.cgi?id=46881
Reported-by: Andi Kleen <andi@firstfloor.org>
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a6fa941d94b411bbd2b6421ffbde6db3c93e65ab upstream.
Don't mess with file refcounts (or keep a reference to file, for
that matter) in perf_event. Use explicit refcount of its own
instead. Deal with the race between the final reference to event
going away and new children getting created for it by use of
atomic_long_inc_not_zero() in inherit_event(); just have the
latter free what it had allocated and return NULL, that works
out just fine (children of siblings of something doomed are
created as singletons, same as if the child of leader had been
created and immediately killed).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120820135925.GG23464@ZenIV.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit cab32f39dcc5b35db96497dc0a026b5dea76e4e7 upstream.
The MCP2515 has a silicon bug causing repeated frame transmission, see section
5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007).
Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually
cause the bug. The workaround proposed by Microchip is to use mode 00 and send
a RTS command on the SPI bus to initiate the transmission.
Signed-off-by: Benoît Locher <Benoit.Locher@skf.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit fcbc50da7753b210b4442ca9abc4efbd4e481f6e upstream.
Avoid constant wakeups caused by noisy irq lines when we don't even care
about the irq. This should be particularly useful for i945g/gm where the
hotplug has been disabled:
commit 768b107e4b3be0acf6f58e914afe4f337c00932b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri May 4 11:29:56 2012 +0200
drm/i915: disable sdvo hotplug on i945g/gm
v2: While at it, remove the bogus hotplug_active read, and do not mask
hotplug_active[0] before checking whether the irq is needed, per discussion
with Daniel on IRC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442
Tested-by: Dominik Köppl <dominik@devwork.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 084b612ecf8e59973576b2f644e6949609c79375 upstream.
Note that gen3 is the only platform where we've got the bit
definitions right, hence the workaround of disabling sdvo hotplug
support on i945g/gm is not due to misdiagnosis of broken hotplug irq
handling ...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: add some blurb about sdvo hotplug fail on i945g/gm I've
wondered about while reviewing.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2:
- Adjust context
- Handle all three cases in i915_driver_irq_postinstall() as there
are not separate functions for gen3 and gen4+
- Carry on using IS_SDVOB() in intel_sdvo_init()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit bf8801145c01ab600f8df66e8c879ac642fa5846 upstream.
From ARM debug architecture v7.1 onwards, a watchpoint exception causes
the DFAR to be updated with the faulting data address. However, DFSR.WnR
takes an UNKNOWN value and therefore cannot be used in general to
determine the access type that triggered the watchpoint.
This patch forbids watchpoints without an overflow handler from
specifying a specific access type (load/store). Those with overflow
handlers must be able to handle false positives potentially triggered by
a watchpoint of a different access type on the same address. For
SIGTRAP-based handlers (i.e. ptrace), this should have no impact.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ba9edaa468869a8cea242a411066b0f490751798 upstream.
Fix the ZTE K5006-Z entry so that it actually matches anything
commit f1b5c997 USB: option: add ZTE K5006-Z
added a device specific entry assuming that the device would use
class/subclass/proto == ff/ff/ff like other ZTE devices. It
turns out that ZTE has started using vendor specific subclass
and protocol codes:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1018 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE LTE Technologies MSM
S: SerialNumber=MF821Vxxxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=86 Prot=10 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=05 Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=00 Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
We do not have any information on how ZTE intend to use these
codes, but let us assume for now that the 3 sets matching
serial functions in the K5006-Z always will identify a serial
function in a ZTE device.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
