| Age | Commit message (Collapse) | Author |
|---|
|
MTD partition for SPI-NOR was not aligned to 8K.
Replace its offset from MTDPART_OFS_APPEND to MTDPART_OFS_NXTBLK.
Signed-off-by: Alejandro Sierra <b18039@freescale.com>
|
|
Since some ethernet MAC flow control is relied on phy pause
status, both link partners exchange information via auto neg to
determine if both parties are capable of flow control.
Advertise phy pause frame to avoid pause frame is not responsed
by the other net node.
Signed-off-by: Fugang Duan <B38611@freescale.com>
|
|
On Uart driver, CTS signal were never disabled
on the imx_set_mctrl function since the register was
written inside of the conditional.
if (mctrl & TIOCM_RTS) {
temp |= UCR2_CTS;
writel(temp, sport->port.membase + UCR2);
}
Signed-off-by: Alejandro Sierra <b18039@freescale.com>
|
|
When do Ethernet UDP stress overnight test with abundance of
data transmission, RX path may hang-on.
Dump the RX BD, found all BD "Empty" bit is cleared, which means
CPU read BD status is not right and waiting here.
Change BD memroy attribute from Normal to strongly ordered:
changes the memory attribute of C=0, B=0 instead of C=0, B=1.
Apply the change, the issue cannot be reproduced.
Signed-off-by: Fugang Duan <B38611@freescale.com>
|
|
Fix chip select for SPI-NOR and
remove flags for no writeable partition for weim nor and
SPI-NOR
Signed-off-by: Alejandro Sierra <b18039@freescale.com>
|
|
* Aline weim-nor partition layout with u-boot expected
offtsets
"bootloader" /dev/mtd0
"bootenv" /dev/mtd1
"kernel" /dev/mtd2
"rootfs" /dev/mtd3
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
|
|
* Aline spi-nor partition layout
* set correct chip-select value
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
|
|
when detect hp inserted, disable speaker; when hp is plugout,
enable speaker.
Signed-off-by: Gary Zhang <b13634@freescale.com>
|
|
Commit 88f5acf88ae6 ("mm: page allocator: adjust the per-cpu counter
threshold when memory is low") changed the form how free_pages is
calculated but it forgot that we used to do free_pages - ((1 << order) -
1) so we ended up with off-by-two when calculating free_pages.
Reported-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change 996M setpoint voltage according to datasheet,
lower VDDARM_CAP from 1.275V to 1.25V, and VDDSOC/PU_CAP
from 1.275V to 1.175V.
Signed-off-by: Anson Huang <b20788@freescale.com>
|
|
There is a USB hang issue when do system suspend/resume test with a USB
device plug in. The issue is caused by USB host driver accessing register
when clock is off. Currently set HCD_FLAG_HW_ACCESSIBLE bit before open
clock in ehci_fsl_bus_resume, it cause accessing register without clock.
So we should change the code call order to avoid driver access register
without clock.
- Set HCD_FLAG_HW_ACCESSIBLE software flag after HW clock turn on
- remove some unnecessary code in ehci_fsl_pre_irq
Signed-off-by: make shi <b15407@freescale.com>
|
|
To adjust the channel support capability, codec dai does not support mono
playback and record, while esai dai does, thus making the whole audio
codec only support stereo and above channel playback/record.
Signed-off-by: Lionel Xu <R63889@freescale.com>
|
|
We must set the DMA mask for esdhc device.
To avoid the following crash when we do not have highmem pages:
[<c0044f90>] (__dabt_svc+0x70/0xa0) from [<c00cf460>]
[<c00cf460>] (mempool_alloc+0x3c/0x108) from [<c00f4aa4>]
[<c00f4aa4>] (blk_queue_bounce+0xc0/0x2fc) from [<c023761c>]
[<c023761c>] (__make_request+0x20/0x2b8) from [<c0235bb4>]
[<c0235bb4>] (generic_make_request+0x3b4/0x4cc) from [<c0235d74>]
[<c0235d74>] (submit_bio+0xa8/0x128) from [<c01279c4>]
[<c01279c4>] (submit_bh+0x108/0x178) from [<c012baa0>]
[<c012baa0>] (block_read_full_pag+e0x278/0x394) from [<c00cd520>]
[<c00cd520>] (do_read_cache_page+0x70/0x154) from [<c00cd64c>]
[<c00cd64c>] (read_cache_page_async+0x1c/0x24) from [<c00cd65c>]
[<c00cd65c>] (read_cache_page+0x8/0x10) from [<c014c354>]
[<c014c354>] (read_dev_sector+0x30/0x68) from [<c014dd4c>]
[<c014dd4c>] (read_lba+0xa0/0x164) from [<c014e300>]
[<c014e300>] (efi_partition+0x9c/0xed4) from [<c014ca0c>]
[<c014ca0c>] (rescan_partitions+0x15c/0x480) from [<c012f190>]
[<c012f190>] (__blkdev_get+0x324/0x394) from [<c012f300>]
[<c012f300>] (blkdev_get+0x100/0x358) from [<c023e5f4>]
[<c023e5f4>] (register_disk+0x140/0x164) from [<c023e73c>]
[<c023e73c>] (add_disk+0x124/0x2a0) from [<c03a7528>]
[<c03a7528>] (mmc_add_disk+0x10/0x68) from [<c03a7820>]
[<c03a7820>] (mmc_blk_probe+0x15c/0x20c) from [<c039cc90>]
[<c039cc90>] (mmc_bus_probe+0x18/0x1c) from [<c0294e28>]
When our DDR size is small or reserved memory are large and
the lowmem can cover all the available pages for kernel,
the highmem pages will not be setup. That means the page_pool
for bounce queue can not be create in init_emergency_pool().
And page_pool will stay NULL without initialized.
In the mmc/card/queue.c the blk_queue_bounce_limit()
function will be called in mmc_init_queue() to
initialize the request_queue and it's bounce_gfp.
If we do not define the DMA mask for our platform,
then the BLK_BOUNCE_HIGH (lowmem pfn) will be set
as limit to queue bounce, which means the blk_queue_bounce
will use page_pool to iterate over the bio segment.
Under the circumstances that highmem is not setup,
the page_pool is null, and causes kernel crash.
After set the DMA mask for esdhci device, the page_pool
will not be used to iterate over the bio segment.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
|
|
Previous setting of PUPSCR is 0x202, which means there is only ~63us
for LDO ramp up, sometimes, system fail to resume by USB remote wake up,
increase this timing to fix USB remote wake up issue.
Signed-off-by: Anson Huang <b20788@freescale.com>
|
|
The log from [MX6DL/S_SD]:
...
mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
dmaengine: failed to get dma1chan0: (-22)
dmaengine: failed to get dma1chan1: (-22)
dmaengine: failed to get dma1chan2: (-22)
dmaengine: failed to get dma1chan3: (-22)
dmaengine: failed to get dma1chan4: (-22)
dmaengine: failed to get dma1chan5: (-22)
dmaengine: failed to get dma1chan6: (-22)
dmaengine: failed to get dma1chan7: (-22)
dmaengine: failed to get dma1chan8: (-22)
dmaengine: failed to get dma1chan9: (-22)
dmaengine: failed to get dma1chan10: (-22)
dmaengine: failed to get dma1chan11: (-22)
dmaengine: failed to get dma1chan12: (-22)
dmaengine: failed to get dma1chan13: (-22)
dmaengine: failed to get dma1chan14: (-22)
dmaengine: failed to get dma1chan15: (-22)
...
It happens when there are many DMA-engine drivers in the system and
dmaengine_get() is called. dmaengine_get() will call dma_chan_get(), which will
call device_alloc_chan_resources() literally on channels of available dma
drivers unless reach -ENODEV. device_alloc_chan_resources() is implemented
in the individual dma drivers, which could return -EINVAL rather than -ENODEV,
then the above messages print out (doesn't hurt, however).
Indeed, the dmaengine_get() and dmaengine_put() is not needed and thus removed.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
1. Fix ENGR00230203 [Android_MX6DL_SD] Gallery: System hang
after resume from suspend during video playback. 20%
2. Fix ENGR00231830 [MX6DL/S_SD] VPU: VPU encode can't
finish and print "VPU blocking: timeout." if suspend/resume. 100%
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
|
|
1. Revert ENGR00231910 Do not disable PU regulator,revert the PU
regulator patch;
2. VPU reset register address is different on MX6 and MX5. It can
fix ENGR00230203 [Android_MX6DL_SD] Gallery: System hang after resume
from suspend during video playback. 20%
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
|
|
When the kernel parses the following cmdline
#mtdparts=gpmi-nand:16m(boot),16m(kernel),1g(home),4g(test),-(usr)
for a big nand chip Micron MT29F64G08AFAAAWP(8GB), we got the following wrong
result:
.............................................
"mtd: partition size too small (0)"
.............................................
We can not get any partition.
The "4g(test)" partition triggers a overflow of the "size". The memparse()
returns 4g to the "size", but the size is "unsigned long" type, so a overflow
occurs, the "size" becomes zero in the end.
This patch changes the "size"/"offset" to "unsigned long long" type,
and replaces the UINT_MAX with ULLONG_MAX for macros SIZE_REMAINING and
OFFSET_CONTINUOUS.
Signed-off-by: Huang Shijie <b32955@freescale.com>
|
|
With onfi a flash is organized into one or more logical units (LUNs).
A" logical unit (LUN) is the minimum unit that can independently execute
commands and report status.
Mtd does not exploit LUN, so make it see a big single flash where size is
lun_size * number_of_lun.
Without this patch MT29F8G08ADBDAH4 size is 512MiB instead of 1GiB.
Artem: split long line on 2 shorter ones.
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
|
|
there is a bug in nand_flash_detect_onfi, busw need to be passed
by pointer to return it.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
|
|
If system enter suspend/resume during VPU encoding on Rigel, there will be
"VPU blocking: timeout." error . But there is ok if enter suspend/resume
during VPU decoding and enter suspend/resume during encoding/decoding on
Arik, until now we didn't know the root cause, so revert it firstly.
Because the previous patch about PU regulator is composed with four commits
and hard to revert, now we adopt simplest way that do not disable PU regulator
in low level. The negative impact is there will several mA increasment in
suspend, we will fix it ASAP.
Signed-off-by: Robin Gong <b38343@freescale.com>
|
|
add clk operation in mxc_pb_spdif_put function
Signed-off-by: Gary Zhang <b13634@freescale.com>
|
|
SD card card detection and NFC controller CS2 share
the same pin on ARD platform. However CS2 is not
connected to the socket. This signal was removed
from the sabreauto board file.
Signed-off-by: Alejandro Sierra <b18039@freescale.com>
|
|
1. correct indent issue
2. when driver is unloaded, remove disable clock operateion and free irq
Signed-off-by: Gary Zhang <b13634@freescale.com>
|
|
not set wm8958 codec as builtin in imx6_defconfig
Signed-off-by: Gary Zhang <b13634@freescale.com>
|
|
Implement set_suspend_voltage for buck switch of PF100, and set_suspend_enable
/set_suspend_disable interface for LDO(VGENx).
Signed-off-by: Robin Gong <b38343@freescale.com>
|
|
There is 6% tolerance for PFM momde in standby so we need set 0.975V(>0.9V+%6)
for VDDSOC and VDDARM which maybe impact system resume ability.
Another two change is:
1.set VDDARM and VDDSOC standby voltage by setting PFUZE register directly,it
is not very friendly.So use more common "state_mem" in constrain of regulator
to set standby voltage.
2.align sabreauto code with sabresd
Signed-off-by: Robin Gong <b38343@freescale.com>
|
|
In mx6q arm2 board, the gpmi conflicts with SD module.
But the defconfig has enabled the gpmi by default.
So we have to add a kernel cmdline to enable the gpmi by hand in arm2 board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
|
|
Add scaling_available_freqs attribute in cpufreq for i.MX
can get cpufreq table info with:
cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies
996000 792000 396000
Signed-off-by: Lin Fuzhen <fuzhen.lin@freescale.com>
|
|
The USB FS eye test will fail in MX6 board if the 3V USB phy LDO is not enabled.
Setting enable bit (bit-0) of LDO 3p0 will make 3p0 LDO to use bandgap output as
reference voltage, LDO output will be accurate. And HW team suggest that it is
better to raise the voltage of USB 3p0 phy LDO 3.2V to pass the USB compliance
testing.
- Implement vdd3p0 regulator enable and disable function to support
enable and disable the LDO 3p0 regulator.
- Use regulator API to enable the USB 3p0 phy LDO and raise the LDO
to 3.2V during system boot up. And disable the LDO before system
enter suspend and enable the LDO again after system resume.
Signed-off-by: make shi <b15407@freescale.com>
|
|
Fix bug: IPU IC resize ratio overflow when downsizing large resolution frame
using split mode, for example downsize 4080x2720 frame into 1920x1080 frame.
Otherwise, the downsized frame is wrong.
Signed-off-by: Wayne Zou <b36644@freescale.com>
|
|
There was a mpr121_touchkey.c driver already upstream,
the orignall driver by 2.6.35 kernel development
should be removed to avoid duplicate.
This reverts commit 3d6df22ad54a14bc8cebb7753c36f7b3cd811665.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
|
|
Export symbol in HDMI core driver to support HDMI AUDIO codec driver's
loadable module build.
Signed-off-by: Chen Liangjun <b36089@freescale.com>
|
|
Export gloable variable in HDMI AUDIO platform driver to support HDMI
AUDIO codec driver's loadable build.
Signed-off-by: Chen Liangjun <b36089@freescale.com>
|
|
HDMI driver can be divided into 3 parts: machine driver, platform
driver, codec driver.To support HDMI AUDIO loadable module build, HDMI
machine driver should be built as loadable.
In this patch, adjust HDMI audio driver's struct: move HDMI audio platform
driver to snd-soc-imx-objs(snd-soc-imx-objs would always be
build-in).In this case, user need only build HDMI AUDIO machine driver
as loadable.
Signed-off-by: Chen Liangjun <b36089@freescale.com>
|
|
This is needed sanity check, because on Ubuntu it's likely that low memory
will happen. This patch also makes this memory allocated from dma zone.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
The settings in the PXP_PS_BUF, PXP_OUT_PS_ULC, and PXP_OUT_PS_LRC will
determine the subset of the PS buffer, or clipped PS source buffer, that
will be used in the output buffer.
HW_PXP_OUT_PS_LRC should set the scaled output size rather than the origin
size when scaling.
Please refer to the "Clipping source images" section in RM for how it works.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
A small logic bug prevents the init sequence from properly turning
off the clocks. This leads to the clocks being always on
if the first update does not complete due to the screen being blanked.
Signed-off-by: Michael Minnick <michael.minnick@freescale.com>
|
|
Only enable power gating for PXP and EPDC. The feature for ELCDIF still need to
be verified.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
Add dependency on CONFIG_FB_MXC_ELCDIF_FB, to avoid build error if as module.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
This is needed when build sii902x hdmi driver as module
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
This can be detected by enabling CONFIG_LOCKDEP and CONFIG_PROVE_LOCKING
The dump log:
=============================================
[ INFO: possible recursive locking detected ]
3.0.35-02140-gb4181ce-dirty #959
---------------------------------------------
swapper/1 is trying to acquire lock:
((fb_notifier_list).rwsem){.+.+.+}, at: [<80088758>] __blocking_notifier_call_chain+0x44/0x88
but task is already holding lock:
((fb_notifier_list).rwsem){.+.+.+}, at: [<80088758>] __blocking_notifier_call_chain+0x44/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock((fb_notifier_list).rwsem);
lock((fb_notifier_list).rwsem);
*** DEADLOCK ***
May be due to missing lock nesting notation
5 locks held by swapper/1:
#0: (&__lockdep_no_validate__){+.+.+.}, at: [<8027f244>] __driver_attach+0x48/0x98
#1: (&__lockdep_no_validate__){+.+.+.}, at: [<8027f254>] __driver_attach+0x58/0x98
#2: (registration_lock){+.+.+.}, at: [<8023a17c>] register_framebuffer+0x18/0x24c
#3: (&fb_info->lock){+.+.+.}, at: [<80238dc8>] lock_fb_info+0x18/0x3c
#4: ((fb_notifier_list).rwsem){.+.+.+}, at: [<80088758>] __blocking_notifier_call_chain+0x44/0x88
stack backtrace:
[<800405c4>] (unwind_backtrace+0x0/0xf8) from [<80097c78>] (__lock_acquire+0x1644/0x1c18)
[<80097c78>] (__lock_acquire+0x1644/0x1c18) from [<80098748>] (lock_acquire+0x84/0x98)
[<80098748>] (lock_acquire+0x84/0x98) from [<804d0aa8>] (down_read+0x34/0x44)
[<804d0aa8>] (down_read+0x34/0x44) from [<80088758>] (__blocking_notifier_call_chain+0x44/0x88)
[<80088758>] (__blocking_notifier_call_chain+0x44/0x88) from [<800887b4>] (blocking_notifier_call_chain+0x18/0x20)
[<800887b4>] (blocking_notifier_call_chain+0x18/0x20) from [<802397e0>] (fb_set_var+0x264/0x290)
[<802397e0>] (fb_set_var+0x264/0x290) from [<8024a320>] (lcd_init_fb+0x54/0x70)
[<8024a320>] (lcd_init_fb+0x54/0x70) from [<8024a3f0>] (lcd_fb_event+0x44/0xb4)
[<8024a3f0>] (lcd_fb_event+0x44/0xb4) from [<80088514>] (notifier_call_chain.isra.1+0x74/0xd0)
[<80088514>] (notifier_call_chain.isra.1+0x74/0xd0) from [<80088774>] (__blocking_notifier_call_chain+0x60/0x88)
[<80088774>] (__blocking_notifier_call_chain+0x60/0x88) from [<800887b4>] (blocking_notifier_call_chain+0x18/0x20)
[<800887b4>] (blocking_notifier_call_chain+0x18/0x20) from [<8023a2d4>] (register_framebuffer+0x170/0x24c)
[<8023a2d4>] (register_framebuffer+0x170/0x24c) from [<8024fe8c>] (mxc_elcdif_fb_probe+0x464/0x564)
[<8024fe8c>] (mxc_elcdif_fb_probe+0x464/0x564) from [<8028031c>] (platform_drv_probe+0x18/0x1c)
[<8028031c>] (platform_drv_probe+0x18/0x1c) from [<8027f0f0>] (driver_probe_device+0x90/0x19c)
[<8027f0f0>] (driver_probe_device+0x90/0x19c) from [<8027f290>] (__driver_attach+0x94/0x98)
[<8027f290>] (__driver_attach+0x94/0x98) from [<8027e2e4>] (bus_for_each_dev+0x5c/0x88)
[<8027e2e4>] (bus_for_each_dev+0x5c/0x88) from [<8027eabc>] (bus_add_driver+0x188/0x250)
[<8027eabc>] (bus_add_driver+0x188/0x250) from [<8027f750>] (driver_register+0x78/0x13c)
[<8027f750>] (driver_register+0x78/0x13c) from [<8001c838>] (mxc_elcdif_fb_init+0x38/0x48)
[<8001c838>] (mxc_elcdif_fb_init+0x38/0x48) from [<80035334>] (do_one_initcall+0x34/0x178)
[<80035334>] (do_one_initcall+0x34/0x178) from [<80008968>] (kernel_init+0x84/0x124)
[<80008968>] (kernel_init+0x84/0x124) from [<8003b614>] (kernel_thread_exit+0x0/0x8)
In fact, we don't need support dynamically switch the framebuffer.
so, we only need do once registeration in probe function.
Signed-off-by: Robby Cai <R63905@freescale.com>
Acked-by: Lily Zhang
|
|
add V4L2_CAP_VIDEO_CAPTURE & V4L2_CAP_STREAMING capability for QUERYCAP ioctl.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
Enable CONFIG_VIDEO_MXC_PXP_V4L2 option.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
It used the hard-coded '0' for historical reason.
This patch changes it to -1 to make video device minor to
be automatically assigned.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
Disable csi clock when inactive, otherwise this prevents system from
entering low power mode.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
The current driver only allows SD cards to run at 1.8V.
This patch allows MMC and SDIO cards to be switched to 1.8V signalling
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
To reproduce:
1. let system enter suspend mode
2. touch the screen
3. after the system resumes, touch screen does not respond again.
The cause:
The touch screen interrupt is triggered by falling edge. During suspend stage,
once the screen has ever been touched, then the interrupt line will be always
pulled low. Since elan ts chip is always powered on and the interrupt gets no
chance to be handled during suspend stage, the interrupt line can not recover
to high to detect a new one.
Workaround:
Read out the pending data to make the touch screen come back alive.
Signed-off-by: LiGang <b41990@freescale.com>
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
* Add ad7280 I2C device support
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Oscar Luna <r01160@freescale.com>
|
|
* Add ADV728x mipi csi2 tvin decoder support
* Perform a hardware reset via i2c command
* Load recommended initial config settings
* Kconfig selection options
* Makefile build rules
Signed-off-by: Oscar Luna <r01160@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
|
