summaryrefslogtreecommitdiff
path: root/drivers/usb/storage
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/usb/storage')
-rw-r--r--drivers/usb/storage/realtek_cr.c28
-rw-r--r--drivers/usb/storage/scsiglue.c16
-rw-r--r--drivers/usb/storage/uas.c50
-rw-r--r--drivers/usb/storage/unusual_devs.h8
-rw-r--r--drivers/usb/storage/unusual_realtek.h5
-rw-r--r--drivers/usb/storage/unusual_uas.h7
6 files changed, 68 insertions, 46 deletions
diff --git a/drivers/usb/storage/realtek_cr.c b/drivers/usb/storage/realtek_cr.c
index 4176d1af9bf2..d955761fce6f 100644
--- a/drivers/usb/storage/realtek_cr.c
+++ b/drivers/usb/storage/realtek_cr.c
@@ -51,7 +51,7 @@ MODULE_VERSION("1.03");
static int auto_delink_en = 1;
module_param(auto_delink_en, int, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(auto_delink_en, "enable auto delink");
+MODULE_PARM_DESC(auto_delink_en, "auto delink mode (0=firmware, 1=software [default])");
#ifdef CONFIG_REALTEK_AUTOPM
static int ss_en = 1;
@@ -776,18 +776,16 @@ static void rts51x_suspend_timer_fn(unsigned long data)
break;
case RTS51X_STAT_IDLE:
case RTS51X_STAT_SS:
- usb_stor_dbg(us, "RTS51X_STAT_SS, intf->pm_usage_cnt:%d, power.usage:%d\n",
- atomic_read(&us->pusb_intf->pm_usage_cnt),
+ usb_stor_dbg(us, "RTS51X_STAT_SS, power.usage:%d\n",
atomic_read(&us->pusb_intf->dev.power.usage_count));
- if (atomic_read(&us->pusb_intf->pm_usage_cnt) > 0) {
+ if (atomic_read(&us->pusb_intf->dev.power.usage_count) > 0) {
usb_stor_dbg(us, "Ready to enter SS state\n");
rts51x_set_stat(chip, RTS51X_STAT_SS);
/* ignore mass storage interface's children */
pm_suspend_ignore_children(&us->pusb_intf->dev, true);
usb_autopm_put_interface_async(us->pusb_intf);
- usb_stor_dbg(us, "RTS51X_STAT_SS 01, intf->pm_usage_cnt:%d, power.usage:%d\n",
- atomic_read(&us->pusb_intf->pm_usage_cnt),
+ usb_stor_dbg(us, "RTS51X_STAT_SS 01, power.usage:%d\n",
atomic_read(&us->pusb_intf->dev.power.usage_count));
}
break;
@@ -820,11 +818,10 @@ static void rts51x_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
int ret;
if (working_scsi(srb)) {
- usb_stor_dbg(us, "working scsi, intf->pm_usage_cnt:%d, power.usage:%d\n",
- atomic_read(&us->pusb_intf->pm_usage_cnt),
+ usb_stor_dbg(us, "working scsi, power.usage:%d\n",
atomic_read(&us->pusb_intf->dev.power.usage_count));
- if (atomic_read(&us->pusb_intf->pm_usage_cnt) <= 0) {
+ if (atomic_read(&us->pusb_intf->dev.power.usage_count) <= 0) {
ret = usb_autopm_get_interface(us->pusb_intf);
usb_stor_dbg(us, "working scsi, ret=%d\n", ret);
}
@@ -1013,12 +1010,15 @@ static int init_realtek_cr(struct us_data *us)
goto INIT_FAIL;
}
- if (CHECK_FW_VER(chip, 0x5888) || CHECK_FW_VER(chip, 0x5889) ||
- CHECK_FW_VER(chip, 0x5901))
- SET_AUTO_DELINK(chip);
- if (STATUS_LEN(chip) == 16) {
- if (SUPPORT_AUTO_DELINK(chip))
+ if (CHECK_PID(chip, 0x0138) || CHECK_PID(chip, 0x0158) ||
+ CHECK_PID(chip, 0x0159)) {
+ if (CHECK_FW_VER(chip, 0x5888) || CHECK_FW_VER(chip, 0x5889) ||
+ CHECK_FW_VER(chip, 0x5901))
SET_AUTO_DELINK(chip);
+ if (STATUS_LEN(chip) == 16) {
+ if (SUPPORT_AUTO_DELINK(chip))
+ SET_AUTO_DELINK(chip);
+ }
}
#ifdef CONFIG_REALTEK_AUTOPM
if (ss_en)
diff --git a/drivers/usb/storage/scsiglue.c b/drivers/usb/storage/scsiglue.c
index 13f2c051dbf2..fd5398efce41 100644
--- a/drivers/usb/storage/scsiglue.c
+++ b/drivers/usb/storage/scsiglue.c
@@ -90,20 +90,8 @@ static int slave_alloc (struct scsi_device *sdev)
sdev->inquiry_len = 36;
/*
- * USB has unusual DMA-alignment requirements: Although the
- * starting address of each scatter-gather element doesn't matter,
- * the length of each element except the last must be divisible
- * by the Bulk maxpacket value. There's currently no way to
- * express this by block-layer constraints, so we'll cop out
- * and simply require addresses to be aligned at 512-byte
- * boundaries. This is okay since most block I/O involves
- * hardware sectors that are multiples of 512 bytes in length,
- * and since host controllers up through USB 2.0 have maxpacket
- * values no larger than 512.
- *
- * But it doesn't suffice for Wireless USB, where Bulk maxpacket
- * values can be as large as 2048. To make that work properly
- * will require changes to the block layer.
+ * Some host controllers may have alignment requirements.
+ * We'll play it safe by requiring 512-byte alignment always.
*/
blk_queue_update_dma_alignment(sdev->request_queue, (512 - 1));
diff --git a/drivers/usb/storage/uas.c b/drivers/usb/storage/uas.c
index 64af88977b03..d022b5ff4cd0 100644
--- a/drivers/usb/storage/uas.c
+++ b/drivers/usb/storage/uas.c
@@ -46,6 +46,7 @@ struct uas_dev_info {
struct scsi_cmnd *cmnd[MAX_CMNDS];
spinlock_t lock;
struct work_struct work;
+ struct work_struct scan_work; /* for async scanning */
};
enum {
@@ -115,6 +116,17 @@ out:
spin_unlock_irqrestore(&devinfo->lock, flags);
}
+static void uas_scan_work(struct work_struct *work)
+{
+ struct uas_dev_info *devinfo =
+ container_of(work, struct uas_dev_info, scan_work);
+ struct Scsi_Host *shost = usb_get_intfdata(devinfo->intf);
+
+ dev_dbg(&devinfo->intf->dev, "starting scan\n");
+ scsi_scan_host(shost);
+ dev_dbg(&devinfo->intf->dev, "scan complete\n");
+}
+
static void uas_add_work(struct uas_cmd_info *cmdinfo)
{
struct scsi_pointer *scp = (void *)cmdinfo;
@@ -800,20 +812,9 @@ static int uas_slave_alloc(struct scsi_device *sdev)
sdev->hostdata = devinfo;
/*
- * USB has unusual DMA-alignment requirements: Although the
- * starting address of each scatter-gather element doesn't matter,
- * the length of each element except the last must be divisible
- * by the Bulk maxpacket value. There's currently no way to
- * express this by block-layer constraints, so we'll cop out
- * and simply require addresses to be aligned at 512-byte
- * boundaries. This is okay since most block I/O involves
- * hardware sectors that are multiples of 512 bytes in length,
- * and since host controllers up through USB 2.0 have maxpacket
- * values no larger than 512.
- *
- * But it doesn't suffice for Wireless USB, where Bulk maxpacket
- * values can be as large as 2048. To make that work properly
- * will require changes to the block layer.
+ * The protocol has no requirements on alignment in the strict sense.
+ * Controllers may or may not have alignment restrictions.
+ * As this is not exported, we use an extremely conservative guess.
*/
blk_queue_update_dma_alignment(sdev->request_queue, (512 - 1));
@@ -843,6 +844,10 @@ static int uas_slave_configure(struct scsi_device *sdev)
sdev->wce_default_on = 1;
}
+ /* Some disks cannot handle READ_CAPACITY_16 */
+ if (devinfo->flags & US_FL_NO_READ_CAPACITY_16)
+ sdev->no_read_capacity_16 = 1;
+
/*
* Some disks return the total number of blocks in response
* to READ CAPACITY rather than the highest block number.
@@ -852,6 +857,12 @@ static int uas_slave_configure(struct scsi_device *sdev)
sdev->fix_capacity = 1;
/*
+ * in some cases we have to guess
+ */
+ if (devinfo->flags & US_FL_CAPACITY_HEURISTICS)
+ sdev->guess_capacity = 1;
+
+ /*
* Some devices don't like MODE SENSE with page=0x3f,
* which is the command used for checking if a device
* is write-protected. Now that we tell the sd driver
@@ -990,6 +1001,7 @@ static int uas_probe(struct usb_interface *intf, const struct usb_device_id *id)
init_usb_anchor(&devinfo->data_urbs);
spin_lock_init(&devinfo->lock);
INIT_WORK(&devinfo->work, uas_do_work);
+ INIT_WORK(&devinfo->scan_work, uas_scan_work);
result = uas_configure_endpoints(devinfo);
if (result)
@@ -1006,7 +1018,9 @@ static int uas_probe(struct usb_interface *intf, const struct usb_device_id *id)
if (result)
goto free_streams;
- scsi_scan_host(shost);
+ /* Submit the delayed_work for SCSI-device scanning */
+ schedule_work(&devinfo->scan_work);
+
return result;
free_streams:
@@ -1174,6 +1188,12 @@ static void uas_disconnect(struct usb_interface *intf)
usb_kill_anchored_urbs(&devinfo->data_urbs);
uas_zap_pending(devinfo, DID_NO_CONNECT);
+ /*
+ * Prevent SCSI scanning (if it hasn't started yet)
+ * or wait for the SCSI-scanning routine to stop.
+ */
+ cancel_work_sync(&devinfo->scan_work);
+
scsi_remove_host(shost);
uas_free_streams(devinfo);
scsi_host_put(shost);
diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index c802aabcc58c..a52ae34fb1c3 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -1277,6 +1277,12 @@ UNUSUAL_DEV( 0x090a, 0x1200, 0x0000, 0x9999,
USB_SC_RBC, USB_PR_BULK, NULL,
0 ),
+UNUSUAL_DEV(0x090c, 0x1000, 0x1100, 0x1100,
+ "Samsung",
+ "Flash Drive FIT",
+ USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+ US_FL_MAX_SECTORS_64),
+
/* aeb */
UNUSUAL_DEV( 0x090c, 0x1132, 0x0000, 0xffff,
"Feiya",
@@ -2119,7 +2125,7 @@ UNUSUAL_DEV( 0x14cd, 0x6600, 0x0201, 0x0201,
US_FL_IGNORE_RESIDUE ),
/* Reported by Michael Büsch <m@bues.ch> */
-UNUSUAL_DEV( 0x152d, 0x0567, 0x0114, 0x0116,
+UNUSUAL_DEV( 0x152d, 0x0567, 0x0114, 0x0117,
"JMicron",
"USB to ATA/ATAPI Bridge",
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
diff --git a/drivers/usb/storage/unusual_realtek.h b/drivers/usb/storage/unusual_realtek.h
index 7ca779493671..dee100dd02e1 100644
--- a/drivers/usb/storage/unusual_realtek.h
+++ b/drivers/usb/storage/unusual_realtek.h
@@ -29,6 +29,11 @@ UNUSUAL_DEV(0x0bda, 0x0138, 0x0000, 0x9999,
"USB Card Reader",
USB_SC_DEVICE, USB_PR_DEVICE, init_realtek_cr, 0),
+UNUSUAL_DEV(0x0bda, 0x0153, 0x0000, 0x9999,
+ "Realtek",
+ "USB Card Reader",
+ USB_SC_DEVICE, USB_PR_DEVICE, init_realtek_cr, 0),
+
UNUSUAL_DEV(0x0bda, 0x0158, 0x0000, 0x9999,
"Realtek",
"USB Card Reader",
diff --git a/drivers/usb/storage/unusual_uas.h b/drivers/usb/storage/unusual_uas.h
index f15aa47c54a9..0eb8c67ee138 100644
--- a/drivers/usb/storage/unusual_uas.h
+++ b/drivers/usb/storage/unusual_uas.h
@@ -163,12 +163,15 @@ UNUSUAL_DEV(0x2537, 0x1068, 0x0000, 0x9999,
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
US_FL_IGNORE_UAS),
-/* Reported-by: Takeo Nakayama <javhera@gmx.com> */
+/*
+ * Initially Reported-by: Takeo Nakayama <javhera@gmx.com>
+ * UAS Ignore Reported by Steven Ellis <sellis@redhat.com>
+ */
UNUSUAL_DEV(0x357d, 0x7788, 0x0000, 0x9999,
"JMicron",
"JMS566",
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
- US_FL_NO_REPORT_OPCODES),
+ US_FL_NO_REPORT_OPCODES | US_FL_IGNORE_UAS),
/* Reported-by: Hans de Goede <hdegoede@redhat.com> */
UNUSUAL_DEV(0x4971, 0x1012, 0x0000, 0x9999,
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-03 11:18:38 +0000