diff options
Diffstat (limited to 'arch/x86/kvm/vmx/nested.c')
| -rw-r--r-- | arch/x86/kvm/vmx/nested.c | 44 |
1 files changed, 33 insertions, 11 deletions
diff --git a/arch/x86/kvm/vmx/nested.c b/arch/x86/kvm/vmx/nested.c index 498fed0dda98..f15ddf58a5bc 100644 --- a/arch/x86/kvm/vmx/nested.c +++ b/arch/x86/kvm/vmx/nested.c @@ -4901,24 +4901,35 @@ static int handle_vmon(struct kvm_vcpu *vcpu) | FEAT_CTL_VMX_ENABLED_OUTSIDE_SMX; /* - * Note, KVM cannot rely on hardware to perform the CR0/CR4 #UD checks - * that have higher priority than VM-Exit (see Intel SDM's pseudocode - * for VMXON), as KVM must load valid CR0/CR4 values into hardware while - * running the guest, i.e. KVM needs to check the _guest_ values. + * Manually check CR4.VMXE checks, KVM must force CR4.VMXE=1 to enter + * the guest and so cannot rely on hardware to perform the check, + * which has higher priority than VM-Exit (see Intel SDM's pseudocode + * for VMXON). * - * Rely on hardware for the other two pre-VM-Exit checks, !VM86 and - * !COMPATIBILITY modes. KVM may run the guest in VM86 to emulate Real - * Mode, but KVM will never take the guest out of those modes. + * Rely on hardware for the other pre-VM-Exit checks, CR0.PE=1, !VM86 + * and !COMPATIBILITY modes. For an unrestricted guest, KVM doesn't + * force any of the relevant guest state. For a restricted guest, KVM + * does force CR0.PE=1, but only to also force VM86 in order to emulate + * Real Mode, and so there's no need to check CR0.PE manually. */ - if (!nested_host_cr0_valid(vcpu, kvm_read_cr0(vcpu)) || - !nested_host_cr4_valid(vcpu, kvm_read_cr4(vcpu))) { + if (!kvm_read_cr4_bits(vcpu, X86_CR4_VMXE)) { kvm_queue_exception(vcpu, UD_VECTOR); return 1; } /* - * CPL=0 and all other checks that are lower priority than VM-Exit must - * be checked manually. + * The CPL is checked for "not in VMX operation" and for "in VMX root", + * and has higher priority than the VM-Fail due to being post-VMXON, + * i.e. VMXON #GPs outside of VMX non-root if CPL!=0. In VMX non-root, + * VMXON causes VM-Exit and KVM unconditionally forwards VMXON VM-Exits + * from L2 to L1, i.e. there's no need to check for the vCPU being in + * VMX non-root. + * + * Forwarding the VM-Exit unconditionally, i.e. without performing the + * #UD checks (see above), is functionally ok because KVM doesn't allow + * L1 to run L2 without CR4.VMXE=0, and because KVM never modifies L2's + * CR0 or CR4, i.e. it's L2's responsibility to emulate #UDs that are + * missed by hardware due to shadowing CR0 and/or CR4. */ if (vmx_get_cpl(vcpu)) { kvm_inject_gp(vcpu, 0); @@ -4928,6 +4939,17 @@ static int handle_vmon(struct kvm_vcpu *vcpu) if (vmx->nested.vmxon) return nested_vmx_fail(vcpu, VMXERR_VMXON_IN_VMX_ROOT_OPERATION); + /* + * Invalid CR0/CR4 generates #GP. These checks are performed if and + * only if the vCPU isn't already in VMX operation, i.e. effectively + * have lower priority than the VM-Fail above. + */ + if (!nested_host_cr0_valid(vcpu, kvm_read_cr0(vcpu)) || + !nested_host_cr4_valid(vcpu, kvm_read_cr4(vcpu))) { + kvm_inject_gp(vcpu, 0); + return 1; + } + if ((vmx->msr_ia32_feature_control & VMXON_NEEDED_FEATURES) != VMXON_NEEDED_FEATURES) { kvm_inject_gp(vcpu, 0); |